liran

  • *
  • 7
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #15 on: October 14, 2016, 09:40:00 pm »
Remove all power from the board and try the manual upgrade:
- Disconnect board from USB
- Hit Upgrade&Erase button
- Connect board to USB port
Removed the usb driver restarted the computer and reinstalled. Now Ok.
Tnx

Sent from my A0001 using Tapatalk


Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #16 on: October 16, 2016, 10:37:30 am »
I just noticed that if I do not have Autotune active in one of my Flight Modes than I could not use SmoothQuick PID adjustment. Essentially when I do not have autotune in FM the whole SystemIndentState section is grayed out.
Sometime it is convenient to have SmoothQuick on.
I understand that it may not be simple to invoke one feature when the whole block is not activated, but may be for next release it is worth to consider.

AutoTune wiki describes what to do to have AutoTune SmoothQuick always active even if AT is not on the FMS.  Just manually enable the AT module and SQ will always be there even without AT on the FMS.

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #17 on: October 21, 2016, 01:17:03 pm »
Hello. New user here. Yesterday I received a Eachine 250.
I was able to update the boot loader (4) and got it to configure fine via the wizard with 15.09

With 16.09 I get no response from the ESCs. If I go back to 15.09 it works fine. I tried a few times. Settings all look the same in both versions.

Also the PFD screen is blank.
MacOS version.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #18 on: October 21, 2016, 01:22:45 pm »
The blank PFD can be fixed with a config reset
File > GCS Config Import / Export > Reset config

Please post your config file while running 16.09
File > Export UAV Settings

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #19 on: October 21, 2016, 02:20:16 pm »
Thanks. The reset config worked for the PFD.

Attached are the two configs, one from the working 15.09 and then the 16.09 that is not working.
« Last Edit: October 21, 2016, 03:35:22 pm by gtstricky »

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #20 on: October 21, 2016, 05:20:52 pm »
Exactly what does this mean. I want to use the new release and i output telemetry out of the rcin port of the flight controller. I recently switched to sbus because of new reciever. So will i be ok using the new release?

Also what is difference between rc1 and rc2?
« Last Edit: October 21, 2016, 05:24:50 pm by jtrout19 »

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #21 on: October 21, 2016, 05:37:29 pm »
Also what is difference between rc1 and rc2?

In first post you can see this link:
https://librepilot.atlassian.net/issues/?filter=10800

Using 16.09 FlexiIO supports telemetry and others options.

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #22 on: October 21, 2016, 05:38:49 pm »
Ok awesome thanks for moving the post I was wondering where the best place to put it would be.

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #23 on: October 21, 2016, 07:36:06 pm »
Hi

Just upgraded a Emax Nighthawk with cc3d atom, Simon 12a esc's from release 15.... to RC2 and I experienced trouble with the ESC calibration.

The Calibration wizard would not fire the motors up no matter which ESC mode I selected. While I got the normal ESC beeps when connecting the battery I never got beeps when in the second phase  once stop was pressed. I got a low value of around 900.

Eventually played in the Configuration Output tab. By linking all motors, selecting PWM 50, SAVING and then powering on I got the motors to run.

Previously I was able to select pwmsync or oneshot and be able to calibrate motors without problem.

Gary

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #24 on: October 21, 2016, 07:46:35 pm »
Not working in windows 10 for. Tries to load then crashes. Good thing i dual boot windows 7 which work great. Other problem i am having is i am not getting any info on my minimosd. Do i have to update that as well and if so where do i get firmware for it? Thanks

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #25 on: October 21, 2016, 08:16:16 pm »
@gtstricky and gazza95
For Esc issues using PwmSyncr with CC3D, try the firmware attached.

Go to the firmware tab, hit rescue.
Open > load the firmware downloaded
Flash

Maybe GCS complains the version do not match but should works.

@jtrout19
The OSD firmware still available at the same place:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup

About crash under Windows10, try installing the Mesa driver.

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #26 on: October 21, 2016, 08:39:15 pm »
@f5soh
I had the OSD setup and working great with 15.09. Get data from the RCinput port of the REVO. Now I only get video. no osd information at all.

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #27 on: October 21, 2016, 11:30:05 pm »
@f5soh, that seemed to do the trick nicely. Will be giving it a flight test tomorrow.

Many thanks.


Gary

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #28 on: October 21, 2016, 11:40:22 pm »
@gtstricky and gazza95
For Esc issues using PwmSyncr with CC3D, try the firmware attached.

Worked!  Thank you.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #29 on: October 21, 2016, 11:52:51 pm »
Thanks for report.
Be safe and use PWM-490Hz for now, maybe there is another issue around.