General Discussion

Pages: [1] 2 3 ... 58

Subject / Started by	Replies / Views	Last post
Revo AuxMag Started by sv2fpv « 1 2 3 ... 26 »	389 Replies 66141 Views	May 01, 2018, 06:18:06 pm by TheOtherCliff
Introducing Flight Test Team Started by liftbag « 1 2 3 ... 8 »	114 Replies 30211 Views	August 07, 2017, 08:22:44 am by Mateusz
Unbricking: Bootloader / resurrection FW if you had non LP / non OP fw on it Started by TheOtherCliff « 1 2 3 ... 7 »	94 Replies 40735 Views	January 22, 2017, 08:33:02 pm by VastSky
Stuck using basic configuration... help! Started by Trailer_Park_Tony_Stark	11 Replies 9489 Views	January 09, 2017, 05:59:24 pm by andycrawforduk
Firmware tab shows unsigned firmware Started by neeraj_shakywal	2 Replies 2676 Views	June 25, 2016, 01:29:43 pm by f5soh
Make sure you use librepilot.org ( .com taken by someone else ) Started by dezent	0 Replies 3185 Views	November 16, 2015, 01:12:58 pm by dezent
Is my CC3D controller dead? Started by robertr	6 Replies 47 Views	Today at 04:43:03 pm by robertr
how do you get the 3 flight mode positons Started by annabell007007	10 Replies 1767 Views	Today at 01:11:05 am by TheOtherCliff
The end of recreational drone and RC model flying in the USA? Started by karla	2 Replies 212 Views	September 14, 2018, 09:19:52 am by Manniose
OPLink Mini - the continuing saga Started by HighAltitude	10 Replies 250 Views	September 06, 2018, 07:57:52 am by TheOtherCliff
Redundant CC3D orientations help clarify please? Started by salukikev	7 Replies 189 Views	September 02, 2018, 06:37:53 am by TheOtherCliff
How to return to default workspaces of program Started by kazmod1	2 Replies 99 Views	August 21, 2018, 07:59:33 pm by kazmod1
My Kingkong is uncontrollable after the upgrade of firmware of flight controller Started by SAkkiE	13 Replies 364 Views	August 18, 2018, 08:48:20 pm by TheOtherCliff
Tarot retractable legs Started by QC102	3 Replies 150 Views	August 16, 2018, 12:40:31 am by QC102
Revo Mini @ Netherlands near Eindhoven, help needed Started by rcbsimoes	1 Replies 68 Views	August 14, 2018, 05:11:26 pm by TheOtherCliff
Able to arm quad in all flight modes. Started by robertr	5 Replies 150 Views	August 10, 2018, 11:50:51 pm by robertr
Turning CC3D axis =/- 90degrees. Started by QC102	2 Replies 143 Views	August 10, 2018, 03:35:20 am by QC102
Quads as assassination weapons: More regulations ahead? Real or not? Started by TheOtherCliff	1 Replies 111 Views	August 06, 2018, 04:06:20 am by karla
cc3d atom mini 3.3v for connecting BMP180 baro Started by sim_tcr	1 Replies 77 Views	August 05, 2018, 09:10:37 am by TheOtherCliff
Revolution board help Started by bterrier	1 Replies 99 Views	August 05, 2018, 06:56:51 am by TheOtherCliff

Pages: [1] 2 3 ... 58

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic
Poll