General Discussion

Pages: 1 [2] 3 4 ... 56

Subject / Started by	Replies / Views	Last post
Screws Loosening mid-air Started by mak24	6 Replies 278 Views	April 02, 2018, 02:19:11 am by mak24
Using Atom for mixer only Started by trust	1 Replies 82 Views	April 01, 2018, 08:11:30 pm by TheOtherCliff
Any tutorials about developing librepilot with eclipse or other IDE? Started by maple_leaf « 1 2 »	16 Replies 454 Views	April 01, 2018, 10:12:25 am by maple_leaf
Debug Naza GPS Started by utoedter	5 Replies 246 Views	March 31, 2018, 09:13:15 pm by utoedter
Some clone OpLinks are bad and some clone Revos have bad RF Started by TheOtherCliff	3 Replies 199 Views	March 26, 2018, 11:05:40 pm by TheOtherCliff
The best antennas for 433mhz Started by TheOtherCliff	0 Replies 117 Views	March 26, 2018, 12:03:27 am by TheOtherCliff
Revolution board Sonar/Pwr port disabled. Started by MikeNH	8 Replies 422 Views	March 24, 2018, 01:24:15 pm by MikeNH
What capabilities does a GPS without a compass bring? Started by MikeNH	5 Replies 249 Views	March 23, 2018, 02:42:55 am by MikeNH
When Starting up system gimbal messes up Stab Started by cary	4 Replies 185 Views	March 21, 2018, 01:57:06 pm by cary
Telemetry host ip address? Started by yutsin1301	1 Replies 107 Views	March 19, 2018, 10:57:53 pm by TheOtherCliff
I need help , can't use my cc3d Started by tsmspace	1 Replies 123 Views	March 19, 2018, 12:11:50 am by f5soh
make package failed unfer Ubuntu14.04LTS Started by maple_leaf	11 Replies 326 Views	March 18, 2018, 05:16:59 pm by maple_leaf
EVENT warning: UAVObject events or callbacks - SmoothQuick Started by karla	12 Replies 387 Views	March 16, 2018, 07:54:58 am by karla
help help help !!!!!!!!!! Started by achutam1	2 Replies 140 Views	March 15, 2018, 04:20:41 pm by TheOtherCliff
Porting LibrePilot to other hardware (F7 boards) Started by Simba741	1 Replies 182 Views	March 13, 2018, 06:13:45 am by TheOtherCliff
HC-06 bluetooth telemetry works, but not with GCS Started by TheOtherCliff	0 Replies 104 Views	March 13, 2018, 02:59:12 am by TheOtherCliff
Suddenly can't use USB cable connection to Revo board from GCS (next) Started by karla	5 Replies 233 Views	March 12, 2018, 08:23:13 pm by TheOtherCliff
HELP Please! CC3D Mini not outputting TX commands Started by cary « 1 2 3 4 »	50 Replies 2420 Views	March 12, 2018, 12:23:15 am by cary
difference in objIds Started by jmyth742	11 Replies 532 Views	March 11, 2018, 11:00:45 pm by jmyth742
Can't get FLYSKY RX and TX to bind. Turningy 9x the problem? Started by Lando	4 Replies 206 Views	March 11, 2018, 10:53:51 am by TheOtherCliff

Pages: 1 [2] 3 4 ... 56

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic
Poll