Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #30 on: October 23, 2016, 06:23:32 pm »
CC3D and TXPID
While craft flies with previous settings there is an oscillation. I have tried to use TXPID to control both Rate KP and Attitude KP for roll and pitch and the aircraft is unflyable. With the update set to always I can see the values are in the range I would expect but it is very unstable. I've previously successfully done this to obtain values of for OPTune. Will go back to setting  things manually.

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #31 on: October 26, 2016, 09:47:56 am »
Vehicle Templates Dialog:
The window for 'vehicle templates' is too long for low resolution screens and needs a vertical scrollbar.

I'm testing on a netbook with 1024x600 (fedora23) and on Win7 with 1024x768. With a screen 768 pixel high, the window fits exactly to the screen, the lower border of the window is cut by the window-taskbar. With a screen about 600 pixel high, you can't use vehicle templates any more, the buttons are below the fold.

Maybe this is a feature-request for Next, but would be nice to have that in 16.09.

f5soh

  • *****
  • 4530
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #32 on: October 26, 2016, 03:24:03 pm »
You will have similar issues with Vehicle wizard, right ?

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #33 on: October 27, 2016, 10:40:46 am »
You will have similar issues with Vehicle wizard, right ?

Yes, but there is only a problem with 600px screen height. The Buttons appear slightly under the fold, you can see the first 4px of the button and they are touchable.

On 1024x768 the wizard is nicely centered and completely visible. Even the "Import template" dialog is complete when i hide the taskbar.

So: low priority, it's only an issue on netbooks with low resolution of 600px vertical.

Thanks.

f5soh

  • *****
  • 4530
    • LibrePilot
« Last Edit: October 27, 2016, 11:22:43 am by f5soh »

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #35 on: November 05, 2016, 12:46:41 am »
I've been posting my experience with 16.09 RC2 in the Multirotor forum, but I thought the following info might be useful here too.  I was unable to complete the transmitter wizard in the new version, so uninstalled it and reinstalled version 15.09.  The wizard works in the older version and my quads are now flying again.
I don't know if this has been formally reported as a potential issue, but it was consistent in my testing.

Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #36 on: November 05, 2016, 05:24:16 am »
I've been posting my experience with 16.09 RC2 in the Multirotor forum, but I thought the following info might be useful here too.  I was unable to complete the transmitter wizard in the new version, so uninstalled it and reinstalled version 15.09.  The wizard works in the older version and my quads are now flying again.
I don't know if this has been formally reported as a potential issue, but it was consistent in my testing.

I'm not sure if this was a change from 15.09 to 16.09RC2, but I've noticed that when I use the main port for my Spektrum DSM receiver, and run the aircraft setup wizard to select DSM input, it switches the DSM input over to the flexi port, and assumes I want to use the flexi port.  The transmitter wizard won't run correctly until I go to the board config and switch DSM back to the main port, and then go to the input button and change all the input channel sources from DSM-flexi to DSM-main.  Then I can complete the transmitter wizard.

Maybe you have a different problem, but I thought I would mention it just in case.

Brunosanta

  • **
  • 54
  • I understand it all but know nothing
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #37 on: November 10, 2016, 08:53:40 pm »
I have downloaded the newest version but the GUI is completly overcrossed and not working on the flight data tab. just info.. check the attached image.
Everybody is only optimistic on the social networks.. being real is hard nowadays

f5soh

  • *****
  • 4530
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #38 on: November 10, 2016, 09:00:36 pm »
Seems you have a wrong install or something...
The PFD file is definitively not the right one.

Do a clean install and reset the GCS config.

Assuming you use the last/newest version, moved post to the RC2 thread
« Last Edit: November 10, 2016, 09:04:34 pm by f5soh »

Brunosanta

  • **
  • 54
  • I understand it all but know nothing
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #39 on: November 10, 2016, 10:20:19 pm »
I will try the fresh install F5soh, thanks for the hint!
Everybody is only optimistic on the social networks.. being real is hard nowadays

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #40 on: November 11, 2016, 04:16:25 am »
Hey guys so I was playing around in the GCS today particularly the Flight Data tab and was looking into the PFD widget. I am assuming the using PFD Arcgis or PFD Readymap shows terrain instead of the blue and brown background image. Thing is they dont work. How would i go about getting these two modes to work correctly? I searched the wiki and nothing came up. Anyone know anything about this?

f5soh

  • *****
  • 4530
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #41 on: November 11, 2016, 09:49:24 am »
There is nothing special to do to get working the terrain display, that why you didn't find info into the wiki.

Some useful info can be the GCS version and OS.

jtrout19

  • ****
  • 334
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #42 on: November 11, 2016, 10:28:17 am »
16.09rc2and i run windows 10

f5soh

  • *****
  • 4530
    • LibrePilot
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #43 on: November 11, 2016, 10:32:06 am »
Posts moved to the 16.09-RC2 thread

Try installing the mesa driver and reset Gcs config.

SamSam

  • *
  • 27
  • Quads Helis planes
Re: Release Candidate - 16.09 RC2 Now available for testing
« Reply #44 on: November 13, 2016, 05:36:19 am »
thanks Guys.. I just downloaded this beta release, did some brief testing, I am already liking it, and the CGS looks good, lot of new features., I have been using CC3d nearly 3yrs, many OP and LP versions, Quads and helis ranging fm 450 to 600, I will be doing lot of testing with this release within next few months, however one problem though, I could not get the I2C to lit up, GPS MAG config, any suggestions...