f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #30 on: March 05, 2016, 09:54:26 pm »
So if you see no changes, there is another issue and you cannot detect or setup a input.

MrFoo

  • *
  • 22
Re: New, need direction
« Reply #31 on: March 12, 2016, 08:42:40 pm »
I was told by helipal to test the continuity between the RX and the FC, specifically the green cable. I tested the continuity between all cables and they all tested OK. Any other suggestions?

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #32 on: March 12, 2016, 08:52:16 pm »
Is the receiver binded ?
Do you see a light on it when powered ?

Post a picture how you connect receiver and cc3d.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #33 on: March 12, 2016, 08:57:59 pm »
Sorry i'm lost now.

What working / not working while you start Transmitter wizard ?

MrFoo

  • *
  • 22
Re: New, need direction
« Reply #34 on: March 12, 2016, 09:27:59 pm »
This is how they are connected

MrFoo

  • *
  • 22
Re: New, need direction
« Reply #35 on: March 12, 2016, 09:34:14 pm »
I believe the receiver is bound. There is a solid red light that comes on when powered.
I am in the transmitter setup wizard. I am on the step where the sticks are being setup. I am able to move the corresponding left stick up and down according to the animation. The next stick is the right one. I try moving all sticks and there is no response on the screen and the setup can't go forward.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #36 on: March 12, 2016, 09:54:12 pm »
What do you mean with left stick ? Throttle ?

Throttle is detected and you can't go forward with others sticks ?

MrFoo

  • *
  • 22
Re: New, need direction
« Reply #37 on: March 12, 2016, 09:54:57 pm »
Correct

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #38 on: March 12, 2016, 10:43:37 pm »
Can you post your config file ? File > Export UAV settings

Do you have some sort of mixing on your Rc Transmitter ?
Like flying wing mixer ?


MrFoo

  • *
  • 22
Re: New, need direction
« Reply #39 on: March 13, 2016, 06:24:57 pm »
I have attached the UAV settings.

I have no clue about any mixing or anything like that.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #40 on: March 13, 2016, 06:55:48 pm »
Try reloading the config attached.

- Connect all wires to receiver
- Power with external battery
- Power on your radio

Check the INPUT status in SystemHealth: Orange ? Green ?

MrFoo

  • *
  • 22
Re: New, need direction
« Reply #41 on: March 13, 2016, 07:53:13 pm »
The input tab is orange. It says the system may be in failsafe mode and failed to update one or more accessory channels.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #42 on: March 13, 2016, 07:58:28 pm »
If after checked you still got nothing about Receiver Activity you can ask for a replacement or try with another board.

https://forum.librepilot.org/index.php?topic=881.msg7245#msg7245

Go to Input tab and check if something move, refresh is slow so put full stick and wait change if any.

jbarchuk

  • ***
  • 129
Re: New, need direction
« Reply #43 on: March 13, 2016, 08:06:17 pm »
- Connect all wires to receiver
- Power with external battery
- Power on your radio

For nit picky completeness, safety, and to avoid confusion, 'power on radio' is #1. Correct?

f5soh

  • *****
  • 4572
    • LibrePilot
Re: New, need direction
« Reply #44 on: March 13, 2016, 08:13:47 pm »
For nit picky completeness, safety, and to avoid confusion, 'power on radio' is #1. Correct?

This allow failsafe testing :)