Revo nano clone on BG?
« on: December 26, 2015, 04:05:28 pm »
say what?
F4, mag, baro.
as always details are kinda sketchy, and sure looks like a lot of ports/connections

FWIW, commenter says it IS a revo and works in GCS 15.05.02

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U
« Last Edit: December 26, 2015, 04:09:09 pm by Thrasher »

liftbag

  • *****
  • 215
    • LibrePilot
Re: Revo nano clone on BG?
« Reply #1 on: December 26, 2015, 04:14:11 pm »
say what?
F4, mag, baro.
as always details are kinda sketchy, and sure looks like a lot of ports/connections

FWIW, commenter says it IS a revo and works in GCS 15.05.02

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U

I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

Re: Revo nano clone on BG?
« Reply #2 on: December 26, 2015, 04:50:43 pm »


I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

so it IS a revo nano clone then?

Brian

  • *
  • 119
Re: Revo nano clone on BG?
« Reply #3 on: December 26, 2015, 04:53:54 pm »
I'ts not really a clone, since it's laid out very differently, and it has the same sensors as the original Revo, but it is a very nice board, and seems to be constructed well.


liftbag

  • *****
  • 215
    • LibrePilot
Re: Revo nano clone on BG?
« Reply #4 on: December 27, 2015, 06:32:02 pm »



I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

so it IS a revo nano clone then?
Not a nano, it's a revolution redesigned.

Re: Revo nano clone on BG?
« Reply #5 on: December 28, 2015, 01:25:52 pm »
Revo,  but seemingly without the integrated 433MHz RF module.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Revo nano clone on BG?
« Reply #6 on: December 28, 2015, 01:35:14 pm »

liftbag

  • *****
  • 215
    • LibrePilot
Re: Revo nano clone on BG?
« Reply #7 on: December 28, 2015, 02:43:46 pm »
Revo,  but seemingly without the integrated 433MHz RF module.
There is a dedicated port for the OPLink Air module, so you can have main and flexi ports free to use with other stuff.
The board is recognized as a full revolution, but the OPLink section is grayed, unless you connect the OPLink Air modem.

daveapplemotors

  • *
  • 245
  • Helis rule
Re: Revo nano clone on BG?
« Reply #8 on: January 04, 2016, 04:50:18 pm »
I want to do autonomous flight with an HK250gt CP helicopter. I have two of them flying well with CC3D nano boards. 

This BG Revo Nano board is good, right. And I don't want FPV but I do want satellite communications, right? Please, point me in the right direction for my sensors that I will need, thanks.

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U
Happy Landings!

Re: Revo nano clone on BG?
« Reply #9 on: January 04, 2016, 11:10:37 pm »
Not related to Nano.  :)

I understand that that is a good one that acts like a Revo but does not have telemetry unless you buy "OpLink AIr" in addition.