LibrePilot Forum

General Category => General Discussion => Topic started by: Thrasher on December 26, 2015, 04:05:28 pm

Title: Revo nano clone on BG?
Post by: Thrasher on December 26, 2015, 04:05:28 pm

say what?
F4, mag, baro.
as always details are kinda sketchy, and sure looks like a lot of ports/connections

FWIW, commenter says it IS a revo and works in GCS 15.05.02

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U

Title: Re: Revo nano clone on BG?
Post by: liftbag on December 26, 2015, 04:14:11 pm

Quote from: Thrasher on December 26, 2015, 04:05:28 pm

say what?
F4, mag, baro.
as always details are kinda sketchy, and sure looks like a lot of ports/connections

FWIW, commenter says it IS a revo and works in GCS 15.05.02

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U

I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

Title: Re: Revo nano clone on BG?
Post by: Thrasher on December 26, 2015, 04:50:43 pm

Quote from: liftbag on December 26, 2015, 04:14:11 pm

I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

so it IS a revo nano clone then?

Title: Re: Revo nano clone on BG?
Post by: Brian on December 26, 2015, 04:53:54 pm

I'ts not really a clone, since it's laid out very differently, and it has the same sensors as the original Revo, but it is a very nice board, and seems to be constructed well.

Title: Re: Revo nano clone on BG?
Post by: liftbag on December 27, 2015, 06:32:02 pm

Quote from: Thrasher on December 26, 2015, 04:50:43 pm

Quote from: liftbag on December 26, 2015, 04:14:11 pm

I'm flying with this board, and it's fine. All works properly and the baro sensor is ok  ;)

so it IS a revo nano clone then?

Not a nano, it's a revolution redesigned.

Title: Re: Revo nano clone on BG?
Post by: rotary65 on December 28, 2015, 01:25:52 pm

Revo,  but seemingly without the integrated 433MHz RF module.

Title: Re: Revo nano clone on BG?
Post by: f5soh on December 28, 2015, 01:35:14 pm

If you want Oplink you should add the "air" oplink.
http://www.banggood.com/Openpilot-OPLINK-Mini-Radio-Telemetry-AIR-And-Ground-For-MINI-CC3D-Revolution-p-1018904.html

(https://forum.librepilot.org/index.php?action=dlattach;topic=488.0;attach=938)

(https://forum.librepilot.org/index.php?action=dlattach;topic=488.0;attach=936)

Title: Re: Revo nano clone on BG?
Post by: liftbag on December 28, 2015, 02:43:46 pm

Quote from: rotary65 on December 28, 2015, 01:25:52 pm

Revo,  but seemingly without the integrated 433MHz RF module.

There is a dedicated port for the OPLink Air module, so you can have main and flexi ports free to use with other stuff.
The board is recognized as a full revolution, but the OPLink section is grayed, unless you connect the OPLink Air modem.

Title: Re: Revo nano clone on BG?
Post by: daveapplemotors on January 04, 2016, 04:50:18 pm

I want to do autonomous flight with an HK250gt CP helicopter. I have two of them flying well with CC3D nano boards. 

This BG Revo Nano board is good, right. And I don't want FPV but I do want satellite communications, right? Please, point me in the right direction for my sensors that I will need, thanks.

http://www.banggood.com/OpenPilot-Mini-CC3D-Revolution-Flight-Controller-For-FPV-Multicopter-5g-p-1018903.html?p=LI16170938632012117U

Title: Re: Revo nano clone on BG?
Post by: TheOtherCliff on January 04, 2016, 11:10:37 pm

Not related to Nano.  :)

I understand that that is a good one that acts like a Revo but does not have telemetry unless you buy "OpLink AIr" in addition.