TMGsi

  • ***
  • 133
Miniosd damaged or not know how to configure
« on: June 03, 2016, 08:55:53 pm »
Hello, I need help.

I bought a miniosd and I am not able to work with cc3d revolution. Miniosd installed and only shows the image of fpv without miniosd information.

Miniosd V.2.2
« Last Edit: June 07, 2016, 10:07:17 pm by f5soh »

hwh

  • *
  • 1018
Re: Miniosd damaged or not know how to configure
« Reply #1 on: June 04, 2016, 02:38:11 am »
That firmware isn't for LP/OP controllers.

The wiki with the setup info for use with cc3d and revo boards is at https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #2 on: June 05, 2016, 12:20:44 am »
Hello, thanks for the help. But still can not configure. I went on the site and downloaded the firmware to three Revo and did not work.

My radio is in PWM mode

What is Lp/Op controllers?

Please help me.

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #3 on: June 05, 2016, 12:28:51 am »
Today I made a test flight with my Robocat270mm with CC3DRevo, the card is very good. Much difference between CC3d. FPV is also very good. Just missing the OSD and GPS.


TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #4 on: June 07, 2016, 07:24:02 pm »
LP/OP means LibrePilot and OpenPilot?

if so, where can I find the firmware to work with librepilot?

or better, which will be easier to make the miniosd function in revo?

hwh

  • *
  • 1018
Re: Miniosd damaged or not know how to configure
« Reply #5 on: June 07, 2016, 07:33:49 pm »
I gave you the link to the firmware and instructions about 4 posts back.

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #6 on: June 07, 2016, 07:53:00 pm »
I think I informed the wrong specification.
I downloaded the firmware you gave me the website did not work.

The especification is written is : MavLink-OSD   V2.2

are different?

hwh

  • *
  • 1018
Re: Miniosd damaged or not know how to configure
« Reply #7 on: June 07, 2016, 08:51:54 pm »
It looks like the same one and their web page says it's compatible.

I don't have one so I can't help you troubleshoot any further.  Maybe someone who has one like @f5soh will answer with more info.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Miniosd damaged or not know how to configure
« Reply #8 on: June 07, 2016, 08:58:37 pm »
Every firmware you can download in wiki page should "work" (i mean osd incrustations), only some options like analog inputs should not match.

Just follow wiki instructions, update charset, firmware.

Be sure the OSD/board is powered with external +5V around 500mA minimum.
Some +5V from some Esc do not provide necessary current.

Please post some pics how you wired OSD

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #9 on: June 07, 2016, 09:29:54 pm »
I have the image without the osd information.
follows the photo

the wires as follows site.

I think the esc provides 5v+, if off lose fpv image
« Last Edit: June 07, 2016, 09:37:11 pm by f5soh »

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Miniosd damaged or not know how to configure
« Reply #10 on: June 07, 2016, 09:36:53 pm »
Are you able to configure / read / save using the config tool you downloaded from wiki page ?

Just powered alone the OSD should display something, be sure you didn't inverted input / output on video connector.

You should provide +12V on Video connector, that power the video chip in your OSD version, looks like the led is on for video side but maybe underpowered, don't know.

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #11 on: June 07, 2016, 09:45:54 pm »
yes, record the firmware and the charset.

arfucam osd config 2.1.3.0 (configtool_minioposd.zip)

the site that mention is : https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup

video wires are correct.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Miniosd damaged or not know how to configure
« Reply #12 on: June 07, 2016, 10:00:34 pm »
Can you talk with OSD using the configTool ?

I mean do some panel changes and save, read.

Try without video input from camera... some high TVL cameras locks the video chip.

TMGsi

  • ***
  • 133
Re: Miniosd damaged or not know how to configure
« Reply #13 on: June 07, 2016, 10:14:31 pm »
see what shows when I took the input video.

My kit fpv is Eachine 600mw

now is with     LP_All_From_Revo2303.hex
« Last Edit: June 07, 2016, 10:21:23 pm by f5soh »

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Miniosd damaged or not know how to configure
« Reply #14 on: June 07, 2016, 10:20:56 pm »
Looks like the Charset is ok (JR130 character) but the text never comes from LP firmware needed, no way...

You still run original firmware flashed on MinimOSD.

You should use this one for Revolution board.
https://librepilot.atlassian.net/wiki/download/attachments/7274504/LP_All_From_Revo2303.hex