lowz

  • *
  • 7
op link binding problem
« on: January 31, 2016, 02:56:18 pm »
After following the guide on how to pair two op link boards, I am still not able to get them to pair. I Have tried using both as coordinator.

Im using the revo board and a op link mini.

op link mini as the coordinator and connected to computer.
The orange tx diode flashes wildly after startup
rx diode does not flash, but in the system tab -> GCSTelemetryStatus RxBytes is counting.
OPLinkStatus RXseq is not counting
Resets is counting.

Any pointers? any more info needed?

f5soh

  • *****
  • 4572
    • LibrePilot
Re: op link binding problem
« Reply #1 on: January 31, 2016, 03:14:20 pm »
Hi,

Post Oplink tab screenshot with oplm1 and oplm2

lowz

  • *
  • 7
Re: op link binding problem
« Reply #2 on: January 31, 2016, 03:31:47 pm »
I see here that the non-coordinator does not seem to send or recieve anything. I tried switching roles on them, the behavior was the same on both cards.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: op link binding problem
« Reply #3 on: January 31, 2016, 04:16:43 pm »
Try with baudrate set to 57600

Set bigger range maybe 25 - 50 for channels ?

Edit: Tried using the same setup like you and it works here.
« Last Edit: January 31, 2016, 04:38:53 pm by f5soh »

lowz

  • *
  • 7
Re: op link binding problem
« Reply #4 on: January 31, 2016, 05:37:06 pm »
no difference unfortunately.

lowz

  • *
  • 7
Re: op link binding problem
« Reply #5 on: January 31, 2016, 05:40:16 pm »
I also tried updating the boot loader on the revo board. And installing new firmware on both of them.
extrnal battery or 5V trough usb for the external card makes no difference.
Is not sending any packages (TX seq no = 0) expected behavour for the non-coordinator board? Or does it say so because it sends telemetry trough USB instead when connected?
And the amount of resets? is that normal?
« Last Edit: January 31, 2016, 05:45:53 pm by lowz »

f5soh

  • *****
  • 4572
    • LibrePilot
Re: op link binding problem
« Reply #6 on: January 31, 2016, 06:07:42 pm »
The coordinator do Tx every time with channel hopping.

The no-coordinator wait on first channel, when a coordinator is received and matches the CoordID field, it do Tx (Coordinator do Rx blink) and jump to next channel same time as coordinator.

The reset on Revo looks like nothing is received from coordinator.

If you have a UHF receiver you can check if Oplink coordinator really do Tx.

lowz

  • *
  • 7
Re: op link binding problem
« Reply #7 on: January 31, 2016, 11:42:32 pm »
I don't have access to a UHF reciver atm. Is there any other way to debug the handshake?
They switch behavour when assigning the revo role as coordinator.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: op link binding problem
« Reply #8 on: February 01, 2016, 12:14:21 am »
If you set the Revo as Coordinator you should see the non-coordinator Rx led blinking+Brief Tx led blinking.

Also find another Oplink so you can detect which side do not work.

lowz

  • *
  • 7
Re: op link binding problem
« Reply #9 on: February 01, 2016, 08:05:34 pm »
Does it log anything?
Is there any more equipment i need to really start to find out what is going on in the board, will order it aswell if im going to get a new oplink.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: op link binding problem
« Reply #10 on: February 01, 2016, 08:30:45 pm »
With a new oplink you can test the first oplink and your revo,  and finally find which side don't work.

Did you inspect the RFM22b module ? Maybe post some macro pictures ?


armond

  • *
  • 5
Re: op link binding problem
« Reply #11 on: March 10, 2016, 04:18:08 pm »
Hello,
Maybe there are any news from you guys in this topic? I have the same binding issue and can not figure out how to make it work.

hwh

  • *
  • 1018
Re: op link binding problem
« Reply #12 on: March 10, 2016, 04:34:35 pm »
There was another similar thread a few days ago and the solution was he forgot to hook up an antenna on one of the boards.  The thread is at https://forum.librepilot.org/index.php?topic=1015.msg7322#msg7322

We all overlook the obvious sometimes.

jtrout19

  • ****
  • 334
Re: op link binding problem
« Reply #13 on: March 10, 2016, 10:23:09 pm »
LOL ;D I love being the example. But yes damn antennas! I left it unplugged.

armond

  • *
  • 5
Re: op link binding problem
« Reply #14 on: March 13, 2016, 07:36:18 pm »
Thanks for reference. The problem is a bit different. The telemetry works perfect (I get data from revo to oplink which is connected to pc). However, I am not able to make PPM Vehicle Control Link to work. Everything is connected to frsky taranis as here: http://opwiki.readthedocs.org/en/latest/user_manual/oplink/control.html but not working. Any ideas what could be wrong?  :)