[cato]

There is a set with oplink, too:
http://www.aliexpress.com/item/OpenPiolot-CC3D-Revolution-Flight-Controller-OPLINK-MINI-NEO-7N-GPS-2-6S-Distribution-Board-for-FPV/32456003983.html?spm=2114.01020208.3.10.Qx0Jih&ws_ab_test=201407_4,201444_6,201409_4

I myself would need with no, as I have an Openpilot OPLM already.

[RC Madman]

^^Nice^^ But this one comes with the M8N GPS and free shipping!http://www.thanksbuyer.com/openpiolot-cc3d-revolution-flight-controller-oplink-mini-and-u-blox-neo-m8n-gps-and-2-6s-distribution-board-41675

[cato]

^^Nice^^ But this one comes with the M8N GPS and free shipping!http://www.thanksbuyer.com/openpiolot-cc3d-revolution-flight-controller-oplink-mini-and-u-blox-neo-m8n-gps-and-2-6s-distribution-board-41675

Looks just exactly like my next revo set

[TheOtherCliff]

That GPS has only one connector and only 4 wires.  It also says that it has a compass.  Is it a OP V9 clone?  ... or is the mag inaccessible or something else?

[RC Madman]

I believe it is a clone. I have seen other sites list them as "OP" ready GPS units.

[TheOtherCliff]

Anybody that gets one, please post and tell us about the mag. 

[cato]

I checked today, beside banggood and aliexpress the revo is not wold via amazon as well. Looks very much like the same trader behind. The prices are between $95 to $140, where Amazon price is mid range. As I was ordering some presents on Amazon today, I added a revo clone for myself

[TheOtherCliff]

The Revo clones I have seen have been around USD $50 (shipped).

[cato]

The Revo clones I have seen have been around USD $50 (shipped).

Yeah, you are right. What I was talking about were the sets of revo, oplink and gps. But I did not check prices closely.

[cato]

Got the Revo clone kit yesterday: Revo with upright connectors, Oplink and a GPS Neo M8N, which looks very much like the Ebay GPS discussed elsewhere here, all three in light and slim cases, cables, 2 antenna with cables, a power distribution board, and a stand for the gps. Nice set, was well packed, looks ok. I will check it in detail during the next days. A first start showed BL 6, but FW 14.06. Upgrade to LP 15.09 worked smoothly. The GPS has a Mag, but it's not recognized, so I will need the External Mag code discussed to get it to work. The GPS works pretty nice and quick, seems to know GPS, Galileo and Glonass, so I got up to 20 (!) sattelites fixed today.

Will do flight tests with LP 15.09 tomorrow

Remark about the cases: I could not make out how to fix them to the frame, so I drilled the necessary holes. 

[TheOtherCliff]

Wow 20 sats!  These new GPS's seem to work really well.  I've got the new cheap Neo8 and it quickly gets 16 sats indoors.

About the cases:  My Nano was the same way.  Don't tell anybody, but I just use servo tape / two faced tape with a careful initial alignment and some thought about how to get it out.  Careful because some kinds (black/gray) of tape are pretty well permanent.  Use the white stuff.

I don't like those vertical pins, so I bought these to convert an old CC3D.  USD $1.09 shipped.  Unsoldering is a pain, must remove black plastic, then unsolder one pin at a time, then clean out all the holes...
http://www.ebay.com/itm/321801383175

[Hayabusa1]

Hey,

i have the same gps and a revo clone!

i have some Problems, my compass always rotates in the ins13 setting, and the board level is not correct in the gcs!

and when i try too fly the copter flys same lika a crap..

when i setting too basic i dont have this problem everything works correct!

i make all calaibrations same as descripted, with the accelerometer calibration i am not sure, the revo board in the picture looks different then my clone, and i am not sure how i must hold in what position

[cato]

Well, the GPS is very good, but the revo is crap. It uses the ARM2 version of the cpu instead of the Z-Version. It works well in complementary mode but acts totally random in EKF mode. the Amazon kit is from good luck buy

Next try

[Hayabusa1]

hmm thats bad whats the difference from the cpu? slower?

what flight controller we can buy for use of all features? sparky 2 clone?

[Mateusz]

hmm thats bad whats the difference from the cpu? slower?

what flight controller we can buy for use of all features? sparky 2 clone?

Versions other than "Z" are prototypes and may have bugs for reference http://www.st.com/st-web-ui/static/active/en/resource/technical/document/errata_sheet/DM00037591.pdf
Workaround
- Revision A devices: none
- Revision Z and 1 devices: fixed

Not sure about revision "ARM 2" or "ARM Y" but original Revolution which I have on my desk has "ARM Z", and so does the clone I got from ebay http://www.ebay.com/itm/351500451307 but it's a risk, maybe I was lucky.