tinou

  • **
  • 83
Re: Minimosd video in black and white
« Reply #15 on: October 29, 2017, 05:39:18 pm »
Hello.

Like i'm waiting my Attopiplot curent sensor i haved connected directly my run and my transmitter for the batterie level.

And..... tatamd 2 or 3 minutes after connect it.. Video on black and white! And after 10mn, the video become very blurred.

So the problem com from my cam or my transmitter or my receiver !! But i think it's runcam!

Re: Minimosd video in black and white
« Reply #16 on: October 29, 2017, 06:02:52 pm »
I had that problem when connecting 12 volts to a camera that needed 8 volts.

Does anything (camera?) feel too warm?  Cameras usually need either 5 volts or 12 volts.

Make sure that everything is powered with minimum voltage as said on instruction sheet.

Good luck.  :)

tinou

  • **
  • 83
Re: Minimosd video in black and white
« Reply #17 on: October 29, 2017, 07:56:39 pm »
I have find the problem!!
Was my runcam setting about day/night automaticly detection.
I have put always on colors and nice!!
I need to wait wendsday 1 november who is public holyday in France for test the result!
Thanks for all your answer.


tinou

  • **
  • 83
Re: Minimosd video in black and white
« Reply #18 on: November 06, 2017, 11:21:16 pm »
I have received a new minimosd, update charset and firmware and ...works!
Rssi at 255% when the radio is on and 45 when it's off.
I need to calibrate it.
I'm waiting for my attopilot current sensor for flight with the osd
Thanks for all

Tongala

  • *
  • 30
Re: Minimosd video in black and white
« Reply #19 on: January 04, 2018, 08:07:18 am »
Very informative. Been wondering how to get analog RSSI in goggles.

But what is the difference between the two hex files for AnalogRSSI ?

LP_All_From_Revo261017+AnalogRSSI_MicroKvteam_pin3.hex
LP_All_From_Revo261017+AnalogRSSI_pin1.hex

And what is the significance of the _pin3 and _pin1 does it refer to wich output pin on RX you use for RSSI?
I'm using frsky xr4sb in sbus mode, the small minoposd and revo.

Thanks would help to know before I pull apart quad. to get to osd.



f5soh

  • *****
  • 4572
    • LibrePilot
Re: Minimosd video in black and white
« Reply #20 on: January 04, 2018, 11:55:31 am »
The two different firmwares refers to two different layouts.
MicroKvteam is the small one and the other (pin1) related to the full sized OSD pcb.

For Rssi you may need a output  in your receiver and add a RC filter between the receiver and OSD-Rssi pin input
Take a look here

tinou

  • **
  • 83
Re: Minimosd video in black and white
« Reply #21 on: January 04, 2018, 12:47:45 pm »
If your rssi output is on pwm you don't need a filter.
Check the voltage of your output.
I have past lot of time for set up my minimosd so if you need help i can help you
« Last Edit: January 04, 2018, 08:17:07 pm by tinou »

Tongala

  • *
  • 30
Re: Minimosd video in black and white
« Reply #22 on: January 05, 2018, 01:00:47 am »
Thank you for quick replies.

And tinou thanks for your work will do as you did to get RSSI, all other aspects of osd work fine.
If I have any problems will get back to you.