mauri64

  • *
  • 21
  • hy
sparky 2.0 e librepilot
« on: August 09, 2017, 08:20:13 am »
salve a tutti, ho installato librepilot 16.09 su w10 quando collego la FC al pc sulla parte bassa viene riconosciuta la sparky, ma non la vedo attiva nella sezione Configuration > Hardware ,infatti compare la scritta "this panel will be updated the relevant controls to let you configure your device once it is connected and running" facendo il wizard a un certo punto mi dice time out, cosa ho tralasciato, grazie a tutti

Re: sparky 2.0 e librepilot
« Reply #1 on: August 09, 2017, 12:58:06 pm »
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab

(Tramite Google translate)
Quando si acquista una nuova Sparky2.0 è necessario:
- aggiornare il bootloader utilizzando l'aggiornatore di avvio con la procedura di salvataggio
- avviare il controller con il nuovo aggiornamento del bootloader e consentirlo di eseguire per alcuni secondi
- quindi "aggiornamento e cancellazione" per lampeggiare il firmware normale, utilizzando la procedura manuale

When you buy a new Sparky2.0 you must:
- update bootloader using the bootloader updater with the rescue procedure
- boot the controller with new bootloader updater and allowed it to run for a few seconds
- then "upgrade and erase" to flash normal firmware, using manual procedure

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #2 on: August 09, 2017, 04:49:49 pm »
could not enter dfu mode, cosa significa?
ho eseguito il ponte su 5 V

Re: sparky 2.0 e librepilot
« Reply #3 on: August 09, 2017, 07:15:35 pm »
Follow directions carefully to: UNPLUG USB then press RESCUE then plug in USB
A few seconds later it will recognize the Sparky2 and give you more options
Then select and flash the bu_sparky2.opfw
Then reboot the Sparky2 and let it run for at least 10 seconds
Then use the "manual method" to "upgrade and erase"
Manual method described here:

Seguire attentamente le istruzioni per: scollegare USB, quindi premere "salvare" (Rescue) quindi collegare USB
Pochi secondi più tardi riconoscerà la Sparky2 e ti darà più opzioni
Quindi selezionare e flash il bu_sparky2.opfw
Quindi riavviate lo Sparky2 e lasciate funzionare per almeno 10 secondi
Quindi utilizzare il "metodo manuale" ("manual method") per "aggiornare e cancellare" ("upgrade and erase")
Metodo manuale ("manual method") descritto qui:
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #4 on: August 09, 2017, 09:28:08 pm »
the librepilot work on windows 10?

f5soh

  • *****
  • 4572
    • LibrePilot
Re: sparky 2.0 e librepilot
« Reply #5 on: August 09, 2017, 10:39:42 pm »
yes, no issue.

If the rescue method do not work, try DFU and windows script (choose 5 or 6 number when asked) :
https://librepilot.atlassian.net/wiki/display/LPDOC/Recover+board+using+DFU

Next you will be able to update using the Manual method (remove SBL solder join !) :
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab#FirmwareTab-Manualmethod

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #6 on: August 11, 2017, 08:45:18 pm »
Work goes well, I miss a few steps

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #7 on: August 14, 2017, 04:24:55 pm »
seguendo il wizard mi chiede il tipo di ESC i miei sono DYS XSD 20A. BLheli S D shot ma non so se sono standard,rapid o one shot......
altro problema, ho individuato che la mia ricevente è PPM ( eseguito bindaggio) quindi collego con 3 cavetti sulla Sparky +-s con ricevente +-s alimento con batteria quando accendo la radio il led mi conferma collecamento, ma librepilot mi dice "NO ACTIVITY" su ricevente....
perchè?

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #8 on: August 16, 2017, 05:00:25 pm »
collegando la ricevente PPM su apposito conettore e alimentando con la batteria, librepilot mi dice NO ACTIVITY, non capisco il motivo, la ricevente sono sicuro che funziona

f5soh

  • *****
  • 4572
    • LibrePilot
Re: sparky 2.0 e librepilot
« Reply #9 on: August 16, 2017, 05:11:27 pm »
Can be bad wiring or PPM change in hardware page that need a reboot.

Be sure the small solder join (only one, usually 5V) is set correctly to power the receiver, some PCB are populated with 10k resistors instead of 0 Ohm resistors.

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #10 on: August 16, 2017, 05:22:25 pm »
I performed a welding on 5 v

f5soh

  • *****
  • 4572
    • LibrePilot
Re: sparky 2.0 e librepilot
« Reply #11 on: August 16, 2017, 05:54:10 pm »
Can you take pictures ?
PPM receiver used ?

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #12 on: August 16, 2017, 08:40:31 pm »
How do i put pictures ??
here

mauri64

  • *
  • 21
  • hy
Re: sparky 2.0 e librepilot
« Reply #13 on: August 16, 2017, 08:45:27 pm »
here

f5soh

  • *****
  • 4572
    • LibrePilot
Re: sparky 2.0 e librepilot
« Reply #14 on: August 16, 2017, 08:54:36 pm »
Is a FS-R6B receiver ? If yes, this receiver do not output PPM signal, only 6ch PWM so you cannot use this one with Sparky2.

FS-iA6B receiver allow IBus and PPM output but i'm not sure is compatible with old FlySky generation radios.