LibrePilot Forum
International Forums => Italiano => Topic started by: mauri64 on August 09, 2017, 08:20:13 am
-
salve a tutti, ho installato librepilot 16.09 su w10 quando collego la FC al pc sulla parte bassa viene riconosciuta la sparky, ma non la vedo attiva nella sezione Configuration > Hardware ,infatti compare la scritta "this panel will be updated the relevant controls to let you configure your device once it is connected and running" facendo il wizard a un certo punto mi dice time out, cosa ho tralasciato, grazie a tutti
-
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab
(Tramite Google translate)
Quando si acquista una nuova Sparky2.0 è necessario:
- aggiornare il bootloader utilizzando l'aggiornatore di avvio con la procedura di salvataggio
- avviare il controller con il nuovo aggiornamento del bootloader e consentirlo di eseguire per alcuni secondi
- quindi "aggiornamento e cancellazione" per lampeggiare il firmware normale, utilizzando la procedura manuale
When you buy a new Sparky2.0 you must:
- update bootloader using the bootloader updater with the rescue procedure
- boot the controller with new bootloader updater and allowed it to run for a few seconds
- then "upgrade and erase" to flash normal firmware, using manual procedure
-
could not enter dfu mode, cosa significa?
ho eseguito il ponte su 5 V
-
Follow directions carefully to: UNPLUG USB then press RESCUE then plug in USB
A few seconds later it will recognize the Sparky2 and give you more options
Then select and flash the bu_sparky2.opfw
Then reboot the Sparky2 and let it run for at least 10 seconds
Then use the "manual method" to "upgrade and erase"
Manual method described here:
Seguire attentamente le istruzioni per: scollegare USB, quindi premere "salvare" (Rescue) quindi collegare USB
Pochi secondi più tardi riconoscerà la Sparky2 e ti darà più opzioni
Quindi selezionare e flash il bu_sparky2.opfw
Quindi riavviate lo Sparky2 e lasciate funzionare per almeno 10 secondi
Quindi utilizzare il "metodo manuale" ("manual method") per "aggiornare e cancellare" ("upgrade and erase")
Metodo manuale ("manual method") descritto qui:
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab
-
the librepilot work on windows 10?
-
yes, no issue.
If the rescue method do not work, try DFU and windows script (choose 5 or 6 number when asked) :
https://librepilot.atlassian.net/wiki/display/LPDOC/Recover+board+using+DFU
Next you will be able to update using the Manual method (remove SBL solder join !) :
https://librepilot.atlassian.net/wiki/display/LPDOC/Firmware+Tab#FirmwareTab-Manualmethod
-
Work goes well, I miss a few steps
-
seguendo il wizard mi chiede il tipo di ESC i miei sono DYS XSD 20A. BLheli S D shot ma non so se sono standard,rapid o one shot......
altro problema, ho individuato che la mia ricevente è PPM ( eseguito bindaggio) quindi collego con 3 cavetti sulla Sparky +-s con ricevente +-s alimento con batteria quando accendo la radio il led mi conferma collecamento, ma librepilot mi dice "NO ACTIVITY" su ricevente....
perchè?
-
collegando la ricevente PPM su apposito conettore e alimentando con la batteria, librepilot mi dice NO ACTIVITY, non capisco il motivo, la ricevente sono sicuro che funziona
-
Can be bad wiring or PPM change in hardware page that need a reboot.
Be sure the small solder join (only one, usually 5V) is set correctly to power the receiver, some PCB are populated with 10k resistors instead of 0 Ohm resistors.
(https://forum.librepilot.org/index.php?action=dlattach;topic=3711.0;attach=6532)
-
I performed a welding on 5 v
-
Can you take pictures ?
PPM receiver used ?
-
How do i put pictures ??
here
-
here
-
Is a FS-R6B receiver ? If yes, this receiver do not output PPM signal, only 6ch PWM so you cannot use this one with Sparky2.
FS-iA6B receiver allow IBus and PPM output but i'm not sure is compatible with old FlySky generation radios.
-
is Flysky AFHDS PPM
-
Model N° FS-R6B do allow PPM output.
Where you see a pinout marking for PPM output ?
http://www.flysky-cn.com/products_detail/productId=47.html
-
i find this
-
This refers to the transmitter FS-T6, not the receiver.
Like many transmitters there is a PPM output for simulator or external module.
-
Can the transmitter FS-T6 transmit with PPM receiver? Which kind ?
-
Looks like the receiver choice is limited and no compatible receivers with PPM output.
(https://forum.librepilot.org/index.php?action=dlattach;topic=3711.0;attach=6549)
-
How can i connect the PWM receiver to sparky2.0?
-
This is not possible.
Sparky2 only support all the 'serial' input protocols (Sbus, PPM, DSM, SRXL, Hott, iBus...), not multiples PWM inputs (and wires).
-
ok
-
Hi, maybe this will help, I don't know for sure... https://tinylink.net/JjNVA (PWM to PPM Encoder).
-
thank you