[javi_pl]

Hi I a new user and I starting with cc3d atom on my tarot 450 sport
 when I have plug the usb and then I conect the battery everything is correct the esc make normal "beep - beep" and I can use the motor. But when I gonna conect just the battery for fly eveyrhing is working less the motor , the esc doesn't make any "beep" but the the servos are working ok.
The esc is a hobbywing platinum 40a.
The esc is ok because my friend has another atom cc3d and here it's work and in my atom cc3d I tried another esc 50a and work in my cc3d but I need work with the hobbywing esc
Somebody know what hapend?
I tried the file program of my friend but is the same I have the same problem


Enviado desde mi iPhone utilizando Tapatalk

[daveapplemotors]

did you do manual calibration on your radio?

[javi_pl]

did you do manual calibration on your radio?

Thank for your fast answer
Yes I configured manualy following the forum my firts step was conect all cables then in the openpilot I went to vehicle tab and select helicopter, then in the input tab I select all the chanels and pwm for the chanel i save and I conect the battery and the esc conect ok I press manual calibration and I save again, after this in output tab i put the range for the servos and the motor I save and everything is working the servos and esc but then when I gonna try conect for fly without usb the esc not working
I hope this is the answer your are waiting
If you want I can qive you more information and the uav file just tell me
Thanks so much for your help


Enviado desde mi iPhone utilizando Tapatalk

[daveapplemotors]

yesJavi,
A UAV might help us figure out what is wrong.

[javi_pl]

Hi dave and everybody this is my uav file for if you can check any problem.
the strange is the same configuration with another ESC  can start the ESC with normaly ¨beep¨ and motor is working I dont know why can not start with the hobbywing ESC 
thanks

[daveapplemotors]

I had one that would not arm (the throttle must go to zero) until I threw the TH (Throttle Hold) switch. My TX didn't go low enough even after manual calibration.

Try using your TH to show your ESC zero throttle. If that works then change a parameter in your TX for low /zero throttle.

I noticed that you have ThrottleCurve2 set the same as curve1. Try this to get negative pitch when you get the motor running:
           <field values="-1,-0.5,0,0.5,1" name="ThrottleCurve2"/>

hope it helps. I will look more in the morning. After I fly if I am lucky enough to have good weather.

                   

[javi_pl]

I had one that would not arm (the throttle must go to zero) until I threw the TH (Throttle Hold) switch. My TX didn't go low enough even after manual calibration.

Try using your TH to show your ESC zero throttle. If that works then change a parameter in your TX for low /zero throttle.

I noticed that you have ThrottleCurve2 set the same as curve1. Try this to get negative pitch when you get the motor running:
           <field values="-1,-0.5,0,0.5,1" name="ThrottleCurve2"/>

hope it helps. I will look more in the morning. After I fly if I am lucky enough to have good weather.

                   

Thanks  Dave
But I was triying with the TH for calibrate and make the same .
An for the trottlecurve I was looking where I can change but I didn't find where is can you tell me what is the tab for change the trottlecurve?
I gonna upload a video with the problem for everybody can see maybe is better


Enviado desde mi iPhone utilizando Tapatalk

[daveapplemotors]

I still haven't figured out your ESC arming thing.

And it might be too cold and windy this morning to fly. I must wait for dawn to find out...

Set the throttle curves to look like the one attachment.

[javi_pl]

thaks dave
I thounk this is for the pithcurve because when I touch here my servos are moving
and the trottle is like before but now I gonna check better.
this is just for the trottlecurve or one of them if for the pithcurve?
I´m uploading a video yet   
maybe one day you can see the video 
thanks

[javi_pl]

This is the video with the problem

Here you can check with electricity I plug the battery and everything is working but with just the battery the ESC doesn't conect.
I was trying the trottlecurve in this that tab and yes I can cahnge from this tab in the left part on the right I can change pithcurve but where can I change the curve in a diferent flight mode?
Thanks for your help!!


Enviado desde mi iPhone utilizando Tapatalk

[javi_pl]

And this is the video with the same configuration but with another ESC



Enviado desde mi iPhone utilizando Tapatalk

[javi_pl]

And this is the video with the same configuration but with another ESC



Enviado desde mi iPhone utilizando Tapatalk

Anybody know the problem for help me ?
Thanks


Enviado desde mi iPhone utilizando Tapatalk

[daveapplemotors]

I have had troubles getting servos to work when not tethered to the USB. I had to start with a fresh UAV file because I could not find where the bit that kept servos inactive. Maybe you have the same issue with ESC. Try a new UAV or try another person's UAV that works and modify it for your servos and radio.

I have puzzled over this one.

good luck and let me know
thanks,
Dave

[javi_pl]

I have had troubles getting servos to work when not tethered to the USB. I had to start with a fresh UAV file because I could not find where the bit that kept servos inactive. Maybe you have the same issue with ESC. Try a new UAV or try another person's UAV that works and modify it for your servos and radio.

I have puzzled over this one.

good luck and let me know
thanks,
Dave

Thank so much dave I gonna try another uav files from here .
Maybe any one can help me.
I was cheking the heli today for try if can fly but the swahsplate moving strange you can check inthis video for if you can help me
This hapend just with the rotor if I dismounting the rotor everything work ok
Thanks


With just the motor and no rotor the stabilization is ok
Why make this?
Thanks

And how can I fix?

[daveapplemotors]

Vibration? Is that causing the axis to tilt. Take off the (flybared???) head and spin just the mainshaft. Maybe remove the rear parts too.

Why do you have a flybar? I think the CC3D will fight with the flybar.   

I assume you did proper Attitude Calibration.     

That jiggle can probably be fixed by putting the throttle neutral just a couple of points higher than minimum.  I may be wrong here. It might be the collective neutral needs to be near minimum. One of my helis has BOTH neutrals near the minimums.