[anthropo]

Mavling OSD keeps showing "disarmed" with Next on Revo with PPM+telemetry. Even, of course, when it is armed !

[f5soh]

There is changes in UAVOs, try this one:

[anthropo]

Thanks, but how to flash with the .hex ? More, do i need to install new next build, do i need to reconfigure the revo ?

[anthropo]

OK i understand that it is the OSD firmware. But when i flash it i don't have throttle, GPS coord, and voltage doesn't work ?

[anthropo]

More informations

[f5soh]

Using a Revo you should use the V/A sensor connected to Revo:
https://librepilot.atlassian.net/wiki/display/LPDOC/Configure+a+Current-Voltage+sensor

GPS coordinates are here in your screen, just truncated with [0.0000] fields that refers to Temperature or Txpid values (temperature field in config tool)
You can choose the temp/txpid info in setup menu with TEMPDISP:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-RCOSDsetuprc_setup_screen

[anthropo]

Thank you. Just one more question : there are many couple of values that match for a voltage divider. FOr example with 3S (12,6V) that could be 100Kohm/33Kohm or 10Kohm/3.3Kohm...

How to choose the best value ?

[anthropo]

I tried with the current voltage, but i still don't see any voltage neither any throttle. I can't enter also enter configuration mode

I saw "Please note the programming cannot be done without DTR pin wired." but i'm using ppm+telemetry. Is is for this reason I can't enter config mode ?

Thanks

[f5soh]

You can choose the divider you want, no need to be precise because you can adjust the factor later.
The only thing is 3.3v max.
Did you configure the Revo for voltage/current sensor ? How are the battery values in PFD ?

Your Throttle field is hidden with the "E 0:00" assuming the time field is in reality a two lines field (you can see the "%" character from Throttle field to the right)
The "E 0:00" extra line field show the time left that come from Revo.

The DTR pin is needed for programming or write firmware / charset if you prefer.
DTR is not needed for regular use with config tool and define panels.

You should enter the setup screen just after boot using the channel toggle you defined:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Channeltoggle

[anthropo]

voltage is 0.00v in pfd...
i still can't enter setup screen. osd boots and nothing can stop that. moving flight mode (what i choose) doesn't permit setup.

i don't have the last next version do i need it ?

[f5soh]

Try using a accessory as toggle switch maybe.
Recent Next should works like the lasted.

You need to configure first the Revo with voltage/current sensor and working in PFD if you want voltage in OSD:
https://librepilot.atlassian.net/wiki/display/LPDOC/Configure+a+Current-Voltage+sensor

[anthropo]

Ok done for the voltage, i didn't configure FlightBatterySettings Properties

But i still have a problem with flight mode (always man) and throttle at 0%

[anthropo]

Luckily i have an another Revo on another racer. It is working as espected with the normal revo.
But it is not working with the mini revo (at least, mine !)

[f5soh]

Should not be related to Revo mini or not mini.
If receiver is powered, Tx calibrated it should work the same.

The "mode switch" works while switching between stab1, stab2, stab3... maybe i will remove this limitation.
Stay 2 seconds in stab2 and switch to stab1 and go back to initial stab2.
This also assumes you changed the refresh rates for ManualControlCommand:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Refreshrates

Panel switching works only without any alarm. (the blinking stuff)

[anthropo]

Still ennoying you : The normal Revo  is perfectly working, even setup mode.

BUT the mini revo doesn't want to enter config mode. That's not a big problem at the moment, for i don't see flight mode (always at Man) and throttle stays at 0%. In GCS, flight data is normal and in configuration, inputs are moving as supposed. That's the main problem at the moment.

There is the same config except the FC : PPM+telemetry, PWR as Voltage sensor, GPS on main port and External Mag on flexi port. tx and rx for telemetry are taken on the flexi-io port

Thank you