startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #30 on: September 14, 2016, 12:03:36 am »
I received neo - 7m gps and the wire welds are not at all well done unfortunately .
I would like confirmation if the compass is integrated in it .
There are the six wires GND, VCC, TXD, RXD, SCL, SDA.
I see a chip L8832036 signed , could be the compass ?
Regards

hwh

  • *
  • 1018
Re: Gps for Revolution
« Reply #31 on: September 14, 2016, 01:41:44 am »
Yes, that is the mag chip.  It should work fine with a revo.  Unlike the Naza ones it will take up both the main and flexi ports.  Since it doesn't have a flash memory chip it won't work with a cc3d.

The first 4 wires (gps and power) go to the main port and the last two (mag) go to the flexi port.  The wiring is in the wiki at https://librepilot.atlassian.net/wiki/display/LPDOC/GPS+setup#GPSsetup-GPSwiring and your gps is the one on the left.
« Last Edit: September 14, 2016, 01:44:52 am by hwh »

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #32 on: September 14, 2016, 11:11:14 pm »
Ok, thank's for information.
I suppose that flash memory chip is the missing chip U2 on the board near Neo 7M?

hwh

  • *
  • 1018
Re: Gps for Revolution
« Reply #33 on: September 14, 2016, 11:15:25 pm »
Yes, that's the one.  It doesn't matter unless you want to use it with a cc3d.  The revo and sparky2 normally (you can disable it) reconfigure the gps with the optimum settings for them every time they boot up.

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #34 on: September 15, 2016, 08:10:31 am »
For now I do not care to use it in flight , but how can I check if the GPS is working properly and receives the satellites?

Inviato dal mio SM-G800F utilizzando Tapatalk


Mateusz

  • *
  • 808
Re: Gps for Revolution
« Reply #35 on: September 15, 2016, 11:19:29 am »
For now I do not care to use it in flight , but how can I check if the GPS is working properly and receives the satellites?

Inviato dal mio SM-G800F utilizzando Tapatalk

In GCS you can see number of satellites and whether it gets a stable 3D lock/fix. If you're losing 3D fix, then you need to wait till it finds more sats.
You might want to consider removing "Inviato dal mio SM-G800F utilizzando Tapatalk" from your forum software for the sake of sanity of other users ;)

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #36 on: September 15, 2016, 11:36:32 am »
I can use GCS 15.09? Connect only main port?
I remove

Mateusz

  • *
  • 808
Re: Gps for Revolution
« Reply #37 on: September 15, 2016, 11:46:57 am »
I can use GCS 15.09? Connect only main port?
I remove

15.09 supports only one GPS+AuxMag unit which is OP Platinum GPSv9 (not produced anymore). It also supports Ublox protocol GPS units, but that's just GPS alone and not very useful if you indention is to use navigation.
16.09-RC1 supports external magnetometer so you can connect Ublox GPS and HMCxxxx mag, it also supports GPS+AuxMag (over I2C) and DJI GPS (unit also contains AuxMag and I recommend this one).
For 16.09-RC see https://forum.librepilot.org/index.php?topic=2266.0

To just test GPS unit alone, you can just connect main-port with 15.09 and it will show sats on Revo. Remember GPS and Mag are two different devices that both are needed for navigation, and it just happens some GPS units have Mag integrated.

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #38 on: September 21, 2016, 08:33:35 pm »

I can connect the cable without perform a wizard?

hwh

  • *
  • 1018
Re: Gps for Revolution
« Reply #39 on: September 21, 2016, 08:54:45 pm »
Yes, just go to the config tab and set the settings for the port(s) you plug it into.

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #40 on: September 21, 2016, 11:19:38 pm »
Yes, just go to the config tab and set the settings for the port(s) you plug it into.
Thanks.
It's just power the revo through the USB cable from the PC or do I connect the battery lipo?

hwh

  • *
  • 1018
Re: Gps for Revolution
« Reply #41 on: September 22, 2016, 05:39:15 am »
USB powers only the flight controller itself, nothing plugged into it gets powered by USB.  To power a GPS (or a receiver) you have to connect the battery.

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #42 on: September 22, 2016, 08:10:28 am »
Ok very well

startrek66

  • ***
  • 156
  • F330+Revo
Re: Gps for Revolution
« Reply #43 on: September 23, 2016, 08:58:21 pm »
USB powers only the flight controller itself, nothing plugged into it gets powered by USB.  To power a GPS (or a receiver) you have to connect the battery.
You know if revo board ports are protect by connection with devices with defects? I'll explain. A device with defects can damage the revo?

hwh

  • *
  • 1018
Re: Gps for Revolution
« Reply #44 on: September 24, 2016, 01:27:54 am »
The original project's revolution had protection on the input ports.  On the various Chinese clones the protection chips are sometimes there, sometimes not.  Even on the ones with the protection chips it's still possible to damage the revo but they make it less likely.

That said, a bad GPS is unlikely to damage the revo.  For the most part it would have to put more than 5 volts onto a revo pin and I've never seen a GPS module that had more than 5 volts on it.