Spiso

  • *
  • 7
Oplink mini do not work on Turnigy 9X as Tx????
« on: January 28, 2016, 09:30:42 pm »
 :-[ :-[ :-[ :-[Please, help me start up my transmitter with Revo board. I want to use Oplink mini as a transmitter module 433 MHz. I have followed the instructions but so far I'm unable to start up. Wizard unresponsive on move  sticks. Health-System INPUT is still red or orange in failsafe mode. Power of Oplink mini module is via 5V linear regulator. Thanks for your answers.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #1 on: January 28, 2016, 09:47:57 pm »
How many PPM channels configured in your radio ?
Should be only 8 channels.

Please post pictures, how is wired and Oplink tab screenshots on both sides

Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #2 on: January 29, 2016, 12:39:58 am »
I have same problem with graupner mx-16 :(
i post the screens soon as i get home...

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #3 on: January 29, 2016, 08:28:20 pm »
I send some photos. Have you some idea? :-[ :'(

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #4 on: January 29, 2016, 08:57:16 pm »
The telemetry link works when you connect the Oplink to USB ?
telemetry works better at 57600bds.

Try moving PPM input to Mainport ?
Double check voltage provided to Oplink.

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #5 on: January 29, 2016, 09:01:26 pm »
How type of input setting I must setting in input card. Oplink or PPM?

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #6 on: January 29, 2016, 09:04:43 pm »
Yes, telemetry works, fine.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #7 on: January 29, 2016, 09:10:01 pm »
Can you try the firmware from here ?

https://forum.librepilot.org/index.php?action=dlattach;topic=312.0;attach=1264

- Rescue
- Connect Oplink
- Open/load file attached
- Flash

No need to erase settings.

Yes, input type should be Oplm.
Without nothing configured go into UavoBrowser, move stick and you should see the ReceiverActivity :

anypis

  • *
  • 26
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #8 on: January 30, 2016, 10:39:19 am »
It is working very well with Turnigy 9X, check my settings on the attach. If you already binded oplink telemetry you have to adjust your RC Input settings as oplink then make "start manula calibration" On every step save settings and reboot oplink and board.

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #9 on: January 30, 2016, 12:47:30 pm »
I tried it all, but without sucess. Can you send exact manual how can i setting my turnigy 9x with openpilot revolution board via oplink. Every side setting (Turnigy 9X(itself menu setting), Oplink mini, Openpilot revolution board, GCS. I have Turnigy 9X wint OpenTx. It can be a problem for oplink mini? Please, Thank you.

anypis

  • *
  • 26
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #10 on: January 30, 2016, 03:25:14 pm »
Can you send your input screen?

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #11 on: January 30, 2016, 06:01:42 pm »
I had a little success. Finally, INPUT is green color. And signal (INPUT) reacts on Turnigy 9X  on/off switch. But that's all. The transmitter does not respond on move of the stick. In manual mode, also it not able calibrate. Individual channels just skiping, but not write a calibration value to the memory.

anypis

  • *
  • 26
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #12 on: January 31, 2016, 05:26:45 pm »
Which firmware you have on your transmitter?

Spiso

  • *
  • 7
Re: Oplink mini do not work on Turnigy 9X as Tx????
« Reply #13 on: January 31, 2016, 10:51:20 pm »
Finally I did it, but through borrowed Turnigy 9X radio with original firmware  ;D. Therefore, the question is: Do I need to set somethink special in OpenTx menu? (firmware 2.17 - latest) or I have damaged my Turnigy 9X radio with OpenTx? Thanks for answers.