Opps

  • **
  • 95
Verification
« on: September 01, 2017, 08:34:39 pm »
.
« Last Edit: September 02, 2017, 06:48:14 am by Wayne'sWorld »

f5soh

  • *****
  • 4007
    • LibrePilot
Re: Verification
« Reply #1 on: September 01, 2017, 08:50:55 pm »
Quote
Can i just use the ground  and signal from flexi and power from pdb.
It's ok. But why do not power the receiver with the same voltage used to power the FC ?
Assuming powering FC with more than 10V is not recommended.

Quote
should  i disable +onshot the reciever port.  And the flexi port to ibus...
Or would pin 8 + oneshot work?
There is no need to run the PPM input in pin8 if you do not use this input.
So the answer is yes, disable the receiver port and use the iBus receiver connected to FlexiPort.


Please be more precise about the issues you read in Wiki.
« Last Edit: September 01, 2017, 08:58:40 pm by f5soh »

Opps

  • **
  • 95
Re: Verification
« Reply #2 on: September 01, 2017, 10:16:21 pm »

.
« Last Edit: September 02, 2017, 06:48:29 am by Wayne'sWorld »

f5soh

  • *****
  • 4007
    • LibrePilot
Re: Verification
« Reply #3 on: September 01, 2017, 10:32:51 pm »
If you are using a Eachine Racer 250 there is a 5v regulator in PCB and all the wiring stuff is already done.
The motor port already provides the +5v power to the CC3D 'clone' board and in fact the same +5v to the FlexiPort for receiver.


Just plug the iBus receiver to the Flexiport according to the wiring and that's all.
The only difference is the FlexiPort found close to the receiver port in your ER250 - CC3D clone.


You are talking about a current sensor, please note the CC3D do not support current sensor.
18V mean the sensor can support this voltage for measurement.
ER250 motors / Esc only support 3S / 4S battery

Quote
Please be more precise about the issues you read in Wiki.
More information ?  ^^
« Last Edit: September 01, 2017, 10:38:47 pm by f5soh »

Opps

  • **
  • 95
Re: Verification
« Reply #4 on: September 01, 2017, 10:43:41 pm »
.
« Last Edit: September 02, 2017, 06:47:43 am by Wayne'sWorld »

Opps

  • **
  • 95
Re: Verification
« Reply #5 on: September 01, 2017, 10:45:58 pm »
 .
« Last Edit: September 02, 2017, 06:47:59 am by Wayne'sWorld »

f5soh

  • *****
  • 4007
    • LibrePilot
Re: Verification
« Reply #6 on: September 01, 2017, 10:51:45 pm »
So please edit previous posts to avoid confusion for others users.
You could also use/add some CR/LF for better clarity in posts.

Opps

  • **
  • 95
Hooking up new rx
« Reply #7 on: September 10, 2017, 03:37:40 pm »
Hello,
I going from pwm to ibus an isix rx to an xsixb rx and when im in the hardware page in the gcs there is no disable-no oneshot in the drop down menu for the receiver port since i hooked the new rx to the flixi port. Right now  my esc`s dont have one shot. So question is can i just select the disable plus one shot for the receiver port to make sure the new rx works properly without flying it and hopefully i can verify on the inputs page that things work and once they do,  then i will switch my esc`s to one shot esc`s. I just dont know what will happen when i select plus oneshot.  Since there is no disable no oneshot like it says there is on the wiki pages.

f5soh

  • *****
  • 4007
    • LibrePilot
Re: Hooking up new rx
« Reply #8 on: September 10, 2017, 04:34:43 pm »
Quote
I just dont know what will happen when i select plus oneshot.

This simply mean the FC is able to output OneShot signals (or other Multishot) but you can still configure outputs as normal 490Hz-PWM or PWMSync signals compatible with your Esc.

If you do the vehicle wizard and choose IBus input and next the RapidEsc (= no OneShot), the wizard will configure all outputs with PWMSync output.

Should i merge this new thread with the old one where you erased all your posts ?
https://forum.librepilot.org/index.php?topic=3794.0

Opps

  • **
  • 95
Re: Hooking up new rx
« Reply #9 on: September 10, 2017, 05:58:39 pm »
Yeah that fine. You said to erase it so people wouldn't get confused. Did i miss understand? 

f5soh

  • *****
  • 4007
    • LibrePilot
Re: Hooking up new rx
« Reply #10 on: September 10, 2017, 06:02:27 pm »
Is the word "edit" same as "erase" for you ?

Opps

  • **
  • 95
Re: Verification
« Reply #11 on: September 10, 2017, 08:08:26 pm »
It must have meant it that day.  When i get home and have access to my computer i will do some editing and make things look correct for someone random that clicks on this thread and needs help with what i did for ibus