CC3D on Align 450 FBL and Taranis
« on: December 05, 2015, 08:24:01 am »
Hi there,

I'm totaly new using a CC3D on a Heli. I've follow this guide so far:

https://frickelnundmehr.wordpress.com/startseite/trex-clone-und-cc3d/

My plan is, to use the CC3D at a Align 450 Pro V2 FBL

But now, I'm struggling at how to connection the cables between CC3D and my X6R Frsky reciver and how to set the correct channels at my Taranis X9d...

could anybody help me?

BTW: I'm using latest openTX Version 2.1.6

cato

  • *
  • 341
Re: CC3D on Align 450 FBL and Taranis
« Reply #1 on: December 05, 2015, 09:02:45 am »
Hi Jamukah,

I have Frsky with X8R. It seems both rx are comparable. There are two options to connect your X6R. If you configured it to use the PWM outputs, simply connect the 6 channels with the main port. A cable for that should be part of your CC3D set.

The second option gives you 16 channels with your X6R, which is to configure it to S-Bus. In this case you would connect your S-Bus output to the Main Port of the CC3D. Again there should be a cable in your set. I used the main port cable with the thre single connectors, works perfect.

How to set up a Heli is not my domain, but there are a few people here who can help you with that part.
Nighthawk 250, MT1806, 12A ESC OneShot125, Revo, M8n GPS, FPV
Cinetank MKII, Elite 2216, 30A Afro OneShot125, Revo Clone, M8N GPS

Re: CC3D on Align 450 FBL and Taranis
« Reply #2 on: December 05, 2015, 09:33:53 am »
Hi Jamukah,

I have Frsky with X8R. It seems both rx are comparable. There are two options to connect your X6R. If you configured it to use the PWM outputs, simply connect the 6 channels with the main port. A cable for that should be part of your CC3D set.

The second option gives you 16 channels with your X6R, which is to configure it to S-Bus. In this case you would connect your S-Bus output to the Main Port of the CC3D. Again there should be a cable in your set. I used the main port cable with the thre single connectors, works perfect.

How to set up a Heli is not my domain, but there are a few people here who can help you with that part.
Hi, Thanks a lot. I alread knew about the diffrent connection ways of the Frsky Recivers.
I ask for the correct Heli Model settings at the Transmitter.  BTW: I already  have connect the CC3D via S-BUS . But thanks again

cato

  • *
  • 341
Re: CC3D on Align 450 FBL and Taranis
« Reply #3 on: December 05, 2015, 09:56:24 am »
Nighthawk 250, MT1806, 12A ESC OneShot125, Revo, M8n GPS, FPV
Cinetank MKII, Elite 2216, 30A Afro OneShot125, Revo Clone, M8N GPS

el_alf

  • *
  • 27
Re: CC3D on Align 450 FBL and Taranis
« Reply #4 on: December 05, 2015, 04:01:26 pm »
Is your trex with    or without flybar? I am trying with a flybarless and it is a success, but without flybar ... disaster! Yesterday it exploded all the blades eway!

Re: CC3D on Align 450 FBL and Taranis
« Reply #5 on: December 05, 2015, 04:35:45 pm »
Is your trex with    or without flybar? I am trying with a flybarless and it is a success, but without flybar ... disaster! Yesterday it exploded all the blades eway!

It's without Paddels, so it is a Flybar Less Head.

el_alf

  • *
  • 27
Re: CC3D on Align 450 FBL and Taranis
« Reply #6 on: December 09, 2015, 05:17:11 pm »
I'm trying a t-rex without flybar and it fly well! If you need concact me for the .uov

Lahiru

  • *
  • 8
  • Build . Fly . Crash . REPEAT
Re: CC3D on Align 450 FBL and Taranis
« Reply #7 on: December 20, 2015, 05:11:26 pm »
Anyone have used cc3d on 450 flybarless heli ?

el_alf

  • *
  • 27
Re: CC3D on Align 450 FBL and Taranis
« Reply #8 on: December 25, 2015, 09:32:56 am »
Anyone have used cc3d on 450 flybarless heli ?

YESSS !  ;)
[https://www.youtube.com/watch?v=Fzs9uP2vcuA]

SamSam

  • *
  • 27
  • Quads Helis planes
Re: CC3D on Align 450 FBL and Taranis
« Reply #9 on: December 30, 2015, 04:06:09 am »
Yes this is very good controller, it took a while to figure out all the settings, as I was done open pilot site went down, so I am exited that this forum is up and running.. I have put together a video how to setup Heli with CC3d. Mine is a trex 450 compatible. here is the link..
« Last Edit: December 30, 2015, 04:09:23 am by SamSam »

SamSam

  • *
  • 27
  • Quads Helis planes
Re: CC3D on Align 450 FBL and Taranis
« Reply #10 on: December 30, 2015, 04:10:34 am »

suzali

  • *
  • 41
Re: CC3D on Align 450 FBL and Taranis
« Reply #11 on: January 16, 2016, 05:44:45 pm »
Anyone have used cc3d on 450 flybarless heli ?

YESSS !  ;)
[https://www.youtube.com/watch?v=Fzs9uP2vcuA]

I saw your video, great !!!
Can you please post or send UAV-file.
Thank you.

SamSam

  • *
  • 27
  • Quads Helis planes
Re: CC3D on Align 450 FBL and Taranis
« Reply #12 on: January 17, 2016, 01:00:07 am »
yep.. here you go..

trex450 compatible, arm - roll right, Throttle  and collective on same stick, works on Open Pilot Ver 15.02.02 ONLY

Re: CC3D on Align 450 FBL and Taranis
« Reply #13 on: January 17, 2016, 04:53:26 am »
Sam Sam , I'm wondering why setups for Open Pilot are being posted here, are you actively trying to get this working on LibrePilot as the members of this forum will most likely want to have assistance with the more recent releases.
 Nevertheless I am sure a lot of your instructions will be applicable. I am still trying to remember how to get a clean and simple heli programed into my Royal Evo/Pro as it been years since I had to change anything but a model name and some minor tweaks!

SamSam

  • *
  • 27
  • Quads Helis planes
Re: CC3D on Align 450 FBL and Taranis
« Reply #14 on: January 18, 2016, 03:22:09 am »
Monell,   Setup procedure is exactly same for Open pilot and Libre pilot. I am sharing my long hours put in, to figure out this controller, with other fellow members so they can benefit from it. It is up to the individual to use it or not use it. UAV files are not cross compatible with different versions, once you know how to setup your controller, you can tweak any UAV file for your version very quickly. I, myself use Libre pilot and Open pilot in my Helis.