Jhinta

  • ***
  • 198
Pinouts
« on: December 04, 2015, 09:58:22 pm »
Can the pinouts be added to wiki?
also is it possible to ad osdmini to flexi-io?
because i have sat and gps allready connected :'(

f5soh

  • *****
  • 4514
    • LibrePilot
Re: Pinouts
« Reply #1 on: December 04, 2015, 10:22:38 pm »

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #2 on: December 05, 2015, 08:17:50 pm »
« Last Edit: December 05, 2015, 11:19:54 pm by Jhinta »

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #3 on: December 05, 2015, 11:22:48 pm »
Q,

Revolution only
Revolution board can provide telemetry on FlexiIO port (receiver port) and also used for MinimOSD programming if DTR pin is wired.

So what i'm wondering, the orange telemetry , can i connect +-&nsig to DTR
or do i need to connect all sens-output to it?

f5soh

  • *****
  • 4514
    • LibrePilot
Re: Pinouts
« Reply #4 on: December 06, 2015, 12:50:40 am »
What you want to do with Orange (receiver?) telemetry here ?

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #5 on: December 06, 2015, 05:12:11 pm »
What you want to do with Orange (receiver?) telemetry here ?
Dx8

f5soh

  • *****
  • 4514
    • LibrePilot
Re: Pinouts
« Reply #6 on: December 06, 2015, 06:27:10 pm »
The telemetry output is only compatible with Gcs or something that understand UavTalk like Oplink or MinOPOSD

You can't connect your Receiver here.

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #7 on: December 06, 2015, 11:45:29 pm »
The telemetry output is only compatible with Gcs or something that understand UavTalk like Oplink or MinOPOSD

You can't connect your Receiver here.

ahh oke ,, will add them manual. tnx

Re: Pinouts
« Reply #8 on: December 07, 2015, 10:52:29 am »
Here is Revo setup example

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #9 on: December 07, 2015, 02:56:28 pm »
Here is Revo setup example
Ow i already have it connected , i was just wondering if telemetry output would work , but i know now its a other protocal , so just had tot add it manual on top of it vbat current and 1 esc temp to get  dx8 working


The last thing i have to mess with is gimball (but witch port , or full auto even possible ? Will see when i get  it )
« Last Edit: December 07, 2015, 03:02:55 pm by Jhinta »

mazevx

  • ***
  • 151
  • Still Learning ...everday
Re: Pinouts
« Reply #10 on: December 10, 2015, 10:33:34 pm »
Only for my better understanding... If I connect the dtr from osd to the revo i can use the revo for programming the osd instead of using an external ftdi?

f5soh

  • *****
  • 4514
    • LibrePilot
Re: Pinouts
« Reply #11 on: December 10, 2015, 11:14:50 pm »
Exactly, config and programming trough Revo using ComBridge

mazevx

  • ***
  • 151
  • Still Learning ...everday
Re: Pinouts
« Reply #12 on: December 10, 2015, 11:36:43 pm »
Thank you!  Im still new to Librepilot and there is a lot to learn...

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #13 on: December 14, 2015, 11:48:12 pm »
Maybe this page can help you ?

https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly



Q
i like to setup a 3d gimball , so far everything is oke , but missing outputs
current setup , sat,gps,currentsensor,4xESC,osd
i can see that i can easly setup a 2D gimbal but what about 3
does flexi-io port profide output when selecting a telemetry profile? (as i need osd)
anyinfo welkom or even re-config suggestion.

Jhinta

  • ***
  • 198
Re: Pinouts
« Reply #14 on: December 17, 2015, 10:52:21 am »
Maybe this page can help you ?

https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly



Q
i like to setup a 3d gimball , so far everything is oke , but missing outputs
current setup , sat,gps,currentsensor,4xESC,osd
i can see that i can easly setup a 2D gimbal but what about 3
does flexi-io port profide output when selecting a telemetry profile? (as i need osd)
anyinfo welkom or even re-config suggestion.
Found a good setup .
Lemon sat with ppm out now i can remove sat and connect telemerty on that port . giving me 5 outputs for gim.