nabreu

  • *
  • 23
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #15 on: October 27, 2015, 01:17:50 pm »
Ok. I will try that and reply. Many thanks for your effort

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #16 on: October 27, 2015, 01:24:21 pm »
You can enter setup screen only a small amount of time just after boot using the Toggle OSd channel. If you miss the right channel, reboot again.

nabreu

  • *
  • 23
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #17 on: October 28, 2015, 12:32:35 am »
Hi.
It's working :) i was using an firmware from OP fórum that uses diferent settings like bat was on pin 1 and i could get into setup anytime i wanted by using the combo i mencioned earlier.

With the one you posted, i can get in the setup by setting channel 5 on the miniosd and using the flight mode switch (channel 5). Could not get it to work on other channel.

The only issue i have is that if i turn the quad on before the rádio, the osd goes directly to setup mode. But i can live with that.

Many thanks for your help.

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #18 on: October 28, 2015, 01:39:12 am »
If you want to use other input for screen switch or to enter in setup screen, you need Accessory set in Config > Input.

The toggle "channel" set on config tool is not the channel from Rc receiver but the order in Rcinput tab :

0 : Throttle
1,2,3 : Roll/pitch/Yaw
5 : Flight mode
6 - 8 : Accessory0 to Accessory2

So if you want to use the "channel6", first setup the accessory0 in Rcinput tab.

I have fixed the issue when osd go to setup screen while RC TX is down yesterday :)
This issue can cause some calibration changes not needed... Check attached hex.


nabreu

  • *
  • 23
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #19 on: October 28, 2015, 03:35:41 pm »
Hi!

All working fine now. Many thanks!

I will soon post all tools i used and how to do it, so that other users can use this OSD

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #20 on: October 28, 2015, 03:56:13 pm »
Maybe time do start a Wiki page ?

I'm confused... we post in Italian section/Post sorry

lucapif

  • *
  • 20
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #21 on: October 28, 2015, 08:14:16 pm »
Pagina Wiki. Ottima idea. A me piacerebbe poter vedere un pò tutto. Sensore corrente collegato alla Revo + GPS V9. OSD micro minim.
Grazie.
Luca

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #22 on: October 28, 2015, 09:09:03 pm »
All info from Revo, no analog inputs on minimOSD
file attached

Edit: Download last firmware from wiki page
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Downloadsdownloads
« Last Edit: February 04, 2016, 11:01:30 pm by f5soh »

lucapif

  • *
  • 20
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #23 on: October 29, 2015, 03:45:38 am »
Merci beaucoup. vous êtes très aimable.
Luca

Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #24 on: February 04, 2016, 10:50:51 pm »
I guys, i have a lot of problem upload firmware in Minimosd with Arducam osdconfig 2.1.3....
With FTDI 232r usb adapter i have this kind of response from Configtool "Can't talk to bootloader, Failed to upload the firmware"
I've Librepilot 15.09 And Minimosd hardware...
I have tried to upload firmware in this post with arduino 1.0.6 but i have a error when verifing the sketch...
any ideas?

f5soh

  • *****
  • 4572
    • LibrePilot
Re: Richiesta ultimo firmware minimosd compatibile con librepilot
« Reply #25 on: February 04, 2016, 10:59:48 pm »
All material is here:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup

Follow steps and don't forget the DTR pin or you can't flash firmware.
No need arduino, firmware can be flashed from config tool (download the one from Wiki page)