[Daxo]

Oh, I see. I was concerned but tbh, I just packed up the power train section and went for a test flight, there seams to be no difference what so ever in flight no matter how hard I pushed it:)

Thank you for the help mate, I feel more confident about my build now! Appreciated!

[onecooler]

Hi folks!

I have tried to setup PPM on flexi port and outputs+oneshot on receiver port and board would not even boot up with such configuration. With disabled+oneshot it did boot but would not read PPM from flexi. I am on 15.09 now. Does anyone use ppm on flexi port? I guess I should start a new topic about this problem, but at first I would like to take a chance here=)

Thanks,
-K.

[f5soh]

yes, me.
i use PPM on flexi.

[onecooler]

yes, me.
i use PPM on flexi.

Really, it does not boot at all with only green light on. Strange. I think I am going to try this with another board

Update: Tried it with another cc3d (the same v2) I have and results are similar. Could you please take a look on my cfg - it might be I am doing something wrong. Thanks in advance.

[Daxo]

Can you please share a screenshot of your Hardware tab and a picture of your CC3D wiring?

[f5soh]

No issue with your config file.

In some cases if you send PWM on PPM input pin the board do not boot.
Be sure the wiring is correct, or remove all wiring to check if board boot first.

[onecooler]

Folks,

I use taranis d4r II and I am sure it outputs ppm as it was connected to receiver pin8 a minute ago and flyable (shorted pin3 and pin4).
What I do is I replace receiver pin 8 with flexi pin 4 (+5 and gnd does not matter - have tried both as suspected power issue), setup board as in my previously attached uav and it does not boot up with battery connected. Strange. I think I am going to try to setup the same on a regular cc3d as I have one somewhere on shelves...

Thanks guys for your inclusion!
-K

[f5soh]

Be sure the PPM servo connector is on the right place.
If connected to the PWM Rssi, this lock the board or do an instant reboot if connected after running.

[Daxo]

Probably a dumb question but better to ask than be sorry later..

My beta prototype is inbound for final tests before the production unit for which I plan to go with RS2205's and with either Littlebee's or RacerStar escs for the build.


Does anyone by any chance had any experience with BLHeli_S fw and CC3D, Racestars support oneShot42 as well, does it work?

Any info is Highly Appreciated!

[Daxo]

Just wanted to add why the dilemma, Folks say they work equally smooth as littlebee , yet the racerstar are at 20% discount right now, at 10$, for 4 that's like 20$ left in my pocket

http://www.banggood.com/Racerstar-RS20A-20A-BLHELI_S-OPTO-2-4S-ESC-Support-Oneshot42-Multishot-for-FPV-Racing-p-1063904.html?p=O521051806009201506W

[f5soh]

OneShot42 or MultiShot are needed for fast loops.
You should only need OneShot125 and didn't notice any change using OneShot42.

[Daxo]

Other than these protocols, I shouldn't have any issues with BLHeli_S firmware right?


Huge Thank you Laurent for all the help!

[Daxo]

Found few threads about it, gonna order a set to check it out.

Will report back how it works.

[Daxo]

Finally got this V2 into my prototype, I find it very practical for this kinda stuff where you just want to build the model asap and begin crash testing, works perfect as any other cc3d flashed with LibrePilot! Love it!

Basic Beginner stock generic settings.

Quad Handling Test Flights;

[feelers12]

Hey I've mine set up and I'm getting very bad lines in my camera feed what can I do both vtx(12v) and camera (5v are been powered from the board