LibrePilot Forum

Users => Vehicles - MultiRotors => Topic started by: Jackbear on October 09, 2016, 10:47:48 pm

Title: Problem accessing minimosd menu
Post by: Jackbear on October 09, 2016, 10:47:48 pm

I can't seem to access my minimosd menu. I have tried the throttle middle, yaw right, pitch forward with no success. I saw somewhere that is was due to a setting with the min and max of the sticks, but I cant find it now.Other than the "battery low" warning flashing, everything works fine. Any help would be greatly appreciated  :-\

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 09, 2016, 11:34:37 pm

You need to configure the channel toggle first:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Channeltoggle
You can enter on Setup Screen just after boot using this channel toggle.

And change some refresh rates or the browsing/set is not so easy:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Refreshrates

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 05:17:18 pm

Thank you! i got it to toggle to the setup menu, but now I dont see where to set the values to turn off the low battery warning. In the setup, the battery warning is set at 0. It reads the correct voltage in the OSD, but the battery percentage flashes as 0%. Its frustrating missing the little things! LOL

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 10, 2016, 09:05:05 pm

What flight controller and OSD firmware are you using ?

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 09:27:36 pm

It's a Revolution board and a minimosd V 1.2 with kv mods. I have all data coming thru the flex io port

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 10, 2016, 09:31:39 pm

So the sensor is connected to Revo board, and alarm comes from Revo ?
Maybe are you using a voltage only basic sensor ?
https://librepilot.atlassian.net/wiki/display/LPDOC/Configure+a+Current-Voltage+sensor#ConfigureaCurrent-Voltagesensor-DisableTIMEalarm

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 09:35:42 pm

Thats correct. Its a voltage only basic sensor

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 09:40:13 pm

And I did set the flight battery capacity to 0 as well

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 10, 2016, 09:46:14 pm

How are the alarms in PFD / SystemHealth ? Something red ?

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 10:01:40 pm

Greens across the board with the proper voltage reading in green as well

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 10, 2016, 10:13:59 pm

Set the "battery warning" value in Setup screen to something real like 10.5 for a 3S

If the voltage is displayed correctly in OSD screen there is no reason to see "Batt low" alarm.

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 10, 2016, 11:06:19 pm

Im using a 4s, so I have it set at 13.6. It still says "Battery Low!", even though it shows 15.07 on the screen.

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 10, 2016, 11:31:04 pm

Try if firmware attached fixes the "Batt low" alarm.

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 11, 2016, 12:28:35 am

Try also this one that should also use the battery alarms from Revo (warning / critical / error) and osd battery level you set in Setup Screen

Title: Re: Problem accessing minimosd menu
Post by: Jackbear on October 16, 2016, 04:44:45 pm

I reflashed the board and did a clean reinstall and it works great! Thank you!

Title: Re: Problem accessing minimosd menu
Post by: f5soh on October 16, 2016, 10:56:11 pm

Great :)

Thanks for testing.