LibrePilot Forum

Users => Vehicles - MultiRotors => Topic started by: MattRody on May 30, 2016, 05:15:03 pm

Title: No Response in Transmitter Wizard
Post by: MattRody on May 30, 2016, 05:15:03 pm

Hey guys,

I have been getting so frustrated trying to set up my Eachine Racer 250. I have been watching so many videos on youtube for following the vehicle wizard and been searching on this forum for answers.

I set up my Eachine using CPPM with only the Black,White,Red cables going to the board. (The white cable is going into the 8th slot) I am using a OrangeRX R615X and a Spektrum DXe. I have had no problems using the Spektrum Dxe with my smaller BNF drones, so hopefully that is not the issue.

After finishing the vehicle wizard and start on the transmitter wizard I can never get the controller to do the "throttle, yaw, pitch" requests it wants you to do in the setup.

Any tips or ideas on what I can do to fix this? Any help would be great!  :-[

Title: Re: No Response in Transmitter Wizard
Post by: f5soh on May 30, 2016, 05:31:16 pm

White wire up maybe ?


(https://forum.librepilot.org/index.php?action=dlattach;topic=1730.0;attach=3255)

Title: Re: No Response in Transmitter Wizard
Post by: MattRody on May 30, 2016, 07:26:24 pm

No still not working even after doing your suggestion.

Any other ideas or videos that could help with this?

Title: Re: No Response in Transmitter Wizard
Post by: f5soh on May 30, 2016, 07:36:36 pm

Receiver still working fine ?

Can you test with a servo connected to normal PWM output ?

You can also try using the FlexiPort as PPM input.

Title: Re: No Response in Transmitter Wizard
Post by: MattRody on May 30, 2016, 07:54:51 pm

Yeah the receiver should still be working fine. I do not have any other larger models or servos to check to see if it is working.

My CC3D has PPM+NoOneShot selected for the receiver port. Is that correct?

Title: Re: No Response in Transmitter Wizard
Post by: f5soh on May 30, 2016, 07:58:40 pm

No, you say PPM was connected to Pin8...
You should select PPM_Pin8-Oneshot in Hardware tab, Save and disconnect all for effective reboot.

Title: Re: No Response in Transmitter Wizard
Post by: MattRody on May 30, 2016, 08:16:20 pm

When I calbrate the ESC in the vehcile wizard should I do OneShot? Or just stick with the middle option "Rapid ESC"

Sorry for so many questions. Just want to get this up and running. I have been working on this all weekend and still cannot figure it out!  :-\

Title: Re: No Response in Transmitter Wizard
Post by: f5soh on May 30, 2016, 08:27:09 pm

If you have OneShot Esc, select OneShot. RapidEsc should be for Simonk.

Title: Re: No Response in Transmitter Wizard
Post by: etopsflight on June 02, 2016, 01:32:16 pm

MattRody

Should the white wire not go right at the end at Pin 8? Looks like you have it on Pin 6. Give it a go!

Etops

Title: Re: No Response in Transmitter Wizard
Post by: gcl_2000 on June 03, 2016, 02:54:01 am

Hi MattRody.

Bind it first and then connect it with the transmitter and go to the wizard set up in Librepilot. Important that you van to choose the correct ESC config,
HTH