[D17E]

Hi all..
need help here for my quad..
i was setup my H quad, but can not fly stable....in hover like rocking or unstable....
and when the wind come....my quad so hard to be controlled...
i was setup like the attach.....(the vid of my setup)
please help me how to setup for suit and stable drone...
thansk so much...
here the picts

[Jhinta]

Why the setup.exe ?

Verstuurd vanaf mijn LG-D855 met Tapatalk

[D17E]

Why the setup.exe ?

Verstuurd vanaf mijn LG-D855 met Tapatalk

setup .exe is my vid....
thats from SCREEN2EXE application....its okay

[D17E]

my quad detail:
FC CC3D BL rev4
A2212 1400kv
esc 30A simonk BEC
Prop 1045 SF
3S 2200 25C
Tx FS I6, Rx FS ia6B
PPM out

[f5soh]

Double check your screenshots, all are unreadable... at least for me.

[D17E]

sorry for my  bad screenshoot..
here my video setup...
be my glade you want to watched...


thanks

[f5soh]

Instead or txPID and simple Roll Rate variable you should use the easyTune feature:
https://librepilot.atlassian.net/wiki/display/LPDOC/EasyTune

That strange you have same PID values for Roll axis and Pitch.
Remove the Tps that should be added at end for very fine tuning.

Be sure the outputs uses OneShot or PwmSync, not PWM-50Hz

[D17E]

Instead or txPID and simple Roll Rate variable you should use the easyTune feature:
https://librepilot.atlassian.net/wiki/display/LPDOC/EasyTune

That strange you have same PID values for Roll axis and Pitch.
Remove the Tps that should be added at end for very fine tuning.

Be sure the outputs uses OneShot or PwmSync, not PWM-50Hz

am i should set the values like the pic..?

thanks

[f5soh]

You should set values in the range you expect for your quad, mean the P term

[D17E]

You should set values in the range you expect for your quad, mean the P term

i still confuse what is PID and what for PID....how to set good values for PID..?
could you mind to teach me how to set for best PID..?
iam newbie here....

thanks

[hwh]

This youtube video is a general explaination of PID.

[D17E]

This youtube video is a general explaination of PID.

hi hwh..
thanks for reply...
i knowed about this vid....
but i can not understand the good value to set PID....

can you share your setup PID...?

[D17E]

here i setup again PID..
but still hard to control hit by the wind....and still flying away...huhuhuhu

[TheOtherCliff]

my quad detail:
FC CC3D BL rev4
A2212 1400kv
esc 30A simonk BEC
Prop 1045 SF
3S 2200 25C
Tx FS I6, Rx FS ia6B
PPM out

10x4.5 SF props are too big for A2212 1400KV motors on 3s lipo.  I run them on A2212 1000KV and they are almost too big there.  I also run 10x4.5 SF cut down to 9x4.5 on A2212 1000KV and they seem about right.

That could be part of your stabil problem.

[TheOtherCliff]

After you put smaller props on your motors (maybe cut down and balance your 10x4.5 to 8.5x4.5, but I would go down to 8x4.5)
if you are still interested in tuning your PIDs, first I would recommend just using default values, not from cloud config or some friend recommendations.    Try that.

If you want to try AutoTune, you can download 16.09 RC and use these instructions.
https://librepilot.atlassian.net/wiki/display/LPDOC/AutoTune