LibrePilot Forum
International Forums => Italiano => Topic started by: mcpll on October 20, 2015, 04:26:12 pm
-
Ciao a tutti,
sotto consiglio di alessio sono a chiedere se qualcuno ha l'ultima versione del firmware di mininosd compatibile con Librepilot.
Questo perchè utilizzando la versione che utilizzavo con openpilot, riuscivo ad vedere quando il modello si armava o meno e i vari cambi di stato.
Così facendo riuscivo a far partire il timer al momento che il modello è armato.
-
Hello,
This one should work :
-
Funziona anche con questo? http://flyduino.net/Micro-MinimOSD_1 (http://flyduino.net/Micro-MinimOSD_1)
-
Yes, works.
There is some mods for analog input pins.
See archive attached, should fit better current 15.09 release.
In OSD_Config.h :
// JRChange: Flight Batt on MinimOSD:
// #define FLIGHT_BATT_ON_MINIMOSD
// Add MicroOSD KV team mod
// #define MICRO_OSD_KVTEAM
// JRChange: Flight Batt on Revo:
#define FLIGHT_BATT_ON_REVO
If you want analog inputs with this really small, you can choose MICRO_OSD_KVTEAM and FLIGHT_BATT_ON_MINIMOSD
FLIGHT_BATT_ON_REVO is used when current sensor is connected to Revo.
Tell me what you want exactly and i can post a .hex file.
Sorry for english...
Laurent
-
Thank you. Ordered. We feel when it arrives. (Google traslate)
Luca
-
Hi!
Great to find this as it´s the only issue i have with Librepilot. Can you post an Hex file compatible with Minimosd micro with KVTeam mod ?
I had it working with OP 15.02 but with Librepilot i get the battery status but not the telemetry.
Also, to calibrate the OSD, is it still possible using the sticks (left Yaw + left Roll) ?
Many Thanks!
-
battery sensor connected to MinimOsd or Revo ?
-
Hi!
Connected to MinimOsd
-
and cc3d or revo ?
-
CC3D, but in a very near future, also Revo ;)
-
Ok,
Try attached hex.
For MICRO_OSD_KVTEAM and all analog inputs : battery / rssi
Battery factors and level still configurable using sticks
-
Hi.
Just test it. Telemetry is working. But battery shows 00.0 and cant calibrate with sticks.
-
Do you access setup screen ?
-
Tried like i used to with left roll and left yaw but did not work.
-
First to enter setup screen you need the "OSD Toggle channel" set with the config tool.
just after boot, move this channel and you enter Setup Screen
"Tried like i uses to with left roll and left yaw but did not work. "
With minOPosd ?
Only one bat pin should works, maybe try the other pin
-
Ok. I will try that and reply. Many thanks for your effort
-
You can enter setup screen only a small amount of time just after boot using the Toggle OSd channel. If you miss the right channel, reboot again.
-
Hi.
It's working :) i was using an firmware from OP fórum that uses diferent settings like bat was on pin 1 and i could get into setup anytime i wanted by using the combo i mencioned earlier.
With the one you posted, i can get in the setup by setting channel 5 on the miniosd and using the flight mode switch (channel 5). Could not get it to work on other channel.
The only issue i have is that if i turn the quad on before the rádio, the osd goes directly to setup mode. But i can live with that.
Many thanks for your help.
-
If you want to use other input for screen switch or to enter in setup screen, you need Accessory set in Config > Input.
The toggle "channel" set on config tool is not the channel from Rc receiver but the order in Rcinput tab :
0 : Throttle
1,2,3 : Roll/pitch/Yaw
5 : Flight mode
6 - 8 : Accessory0 to Accessory2
So if you want to use the "channel6", first setup the accessory0 in Rcinput tab.
I have fixed the issue when osd go to setup screen while RC TX is down yesterday :)
This issue can cause some calibration changes not needed... Check attached hex.
-
Hi!
All working fine now. Many thanks!
I will soon post all tools i used and how to do it, so that other users can use this OSD
-
Maybe time do start a Wiki page ?
I'm confused... we post in Italian section/Post sorry
-
Pagina Wiki. Ottima idea. A me piacerebbe poter vedere un pò tutto. Sensore corrente collegato alla Revo + GPS V9. OSD micro minim.
Grazie.
-
All info from Revo, no analog inputs on minimOSD
file attached
Edit: Download last firmware from wiki page
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Downloadsdownloads
-
Merci beaucoup. vous êtes très aimable.
-
I guys, i have a lot of problem upload firmware in Minimosd with Arducam osdconfig 2.1.3....
With FTDI 232r usb adapter i have this kind of response from Configtool "Can't talk to bootloader, Failed to upload the firmware"
I've Librepilot 15.09 And Minimosd hardware...
I have tried to upload firmware in this post with arduino 1.0.6 but i have a error when verifing the sketch...
any ideas?
-
All material is here:
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup
Follow steps and don't forget the DTR pin or you can't flash firmware.
No need arduino, firmware can be flashed from config tool (download the one from Wiki page)