LibrePilot Forum
General Category => General Discussion => Topic started by: Pe64p on February 10, 2018, 05:38:24 pm
-
I have had a CC3D board in a 250 quad that I built 3 or 4 years ago was working when I put it away a year ago
so decided to fly her again
my old GCS was the open Pilot so upgraded that to Libre Pilot at first everything checked out and was getting ready to set up the flight controls (TX) they Horizon and heading was working and all that and then found out that the RX had shot craps so got a new one bound it up and was getting to finish setting it up
now the Board will not respond tried the rescue mode Tried pushing the button then connecting it it says its loading firmware and the light flashes fast then I get a timed out message
look up every possible thing I can find and tried but no go
did the board Die on me ?? should I get a new one of these or get some other style or Brand? I don't race Don't FPV yet but would like to do that
-
Looks like your board works fine, fast blinking leds is related to gyro initialization.
You should try another USB cable and double check if USB socket is fine in your board.
-
thanks yes the lights blink like they should
will try another cable i have tried 3 different Ports on the computer so that is not it but will try the cable should have another one around here somewere :)
-
Could it be that it needs the new version of bootloader?
-
its on Boot loader Ver 4 isn't that the latest on ?
now I even bought a NEW CC3D board and its acting the same way
I loaded an older version 15.09 I think and it shows up afterwards but you cant get past that first area on EITHER BOARD if you hit Rescue it shows the board and there is a "blue I" over on the side and it shows the Version after upgrading back to 16.09 but it times out and that's as far as it goes cant make it do anything else
it says something about "Time out load manually" but I have not been able to figure out how to do that
my computer is a Windows 10 and I keep it updated right now I'm updateing my Laptop and going to try that
I'm stumped might have to go to another Board design if I cant make this work
Help
-
If when connecting the board after hit the Rescue button (or Upgrade&Erase button) do nothing and finally show a timed out (whatever the bootloader version in this case), you may have a issue with USB cable.
-
have 2 cables and they both do the same thing that was my first thought
it loads up the latest firmware but then times out
looking for another cable and even firing up and updateing my laptop to try
I'm Stumped
-
Try a different computer if just for a test.
Try uninstalling and reinstalling LP.
-
Up date on this issue fired up my old Laptop it is Windows 10 had to install all the updates but finally got it up and running stable Installed Libre Pilot and plugged in the NEW Board and Hit upgrade and it took off did more things than what my Desktop but then when it was trying to reboot everything just Froze Stopped what ever could not log out shut down anything had to push the button on the computer to shut everything down and start over. Tried doing the Rescue thing. it would identify the board but could not get it to do anything else SO
Drug out the old Board installed it and fired it up did the upgrade and remove and it just took off everything works got it all set up and the Transmitter is talking to it and its Responding now I get to clean it all up and wire tie everything in place and I'm ready
Now there is one thing I notice My Desktop system kept coming up with a message that it could not recognize this USB device and the Lap top said it did Recognize it and the light bar down in the bottom had several lights lit up on the RX side NOW
I would like to use my Desktop just because its handier Question Do I have to get some USB Drivers to load on it so it recognizes the board both systems are Windows 10 and I keep them updated What can I do ????
Next I would like to try FPV any suggestions for a Low budget items just to try it out NO RACING IM old my SPEED DAYs are over
Thanks for everyone's Help
-
found the issue Had to Delete the one Composite USB port and reinstall it now it all works
IM a HAPPY CAMPER :)
Now I need on converting this to an inexpensive FPV want to try it out cause I lost Sight in One eye after having a stroke last year Need to be on the Cheap side and might need help hooking it all up in this 250 frame
again Thanks everyone for your help
now on to FPV
-
FPV can be pretty easy.
Airborne:
- AIO (all in one) with camera, transmitter, and antenna can be as cheap as $25
For display:
- very cheap FPV goggles can be about $45 but beware that all inexpensive FPV goggles require you to wear reading glasses if you are not near sighted. That includes the ones that have an adjustment for this.
- or a $8 video to USB adapter that you use with your laptop screen (must buy an FPV receiver in addition to this)