LibrePilot Forum
Development => Hardware => Topic started by: Jhinta on December 04, 2015, 09:58:22 pm
-
Can the pinouts be added to wiki?
also is it possible to ad osdmini to flexi-io?
because i have sat and gps allready connected :'(
-
Maybe this page can help you ?
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly
-
Maybe this page can help you ?
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly
:o hmm how didnt i find that , puur shame now :-[ tnx
-
Q,
Revolution only
Revolution board can provide telemetry on FlexiIO port (receiver port) and also used for MinimOSD programming if DTR pin is wired.
So what i'm wondering, the orange telemetry , can i connect +-&nsig to DTR
or do i need to connect all sens-output to it?
-
What you want to do with Orange (receiver?) telemetry here ?
-
What you want to do with Orange (receiver?) telemetry here ?
Dx8
-
The telemetry output is only compatible with Gcs or something that understand UavTalk like Oplink or MinOPOSD
You can't connect your Receiver here.
-
The telemetry output is only compatible with Gcs or something that understand UavTalk like Oplink or MinOPOSD
You can't connect your Receiver here.
ahh oke ,, will add them manual. tnx
-
Here is Revo setup example
-
Here is Revo setup example
Ow i already have it connected , i was just wondering if telemetry output would work , but i know now its a other protocal , so just had tot add it manual on top of it vbat current and 1 esc temp to get dx8 working
The last thing i have to mess with is gimball (but witch port , or full auto even possible ? Will see when i get it )
-
Only for my better understanding... If I connect the dtr from osd to the revo i can use the revo for programming the osd instead of using an external ftdi?
-
Exactly, config and programming trough Revo using ComBridge
-
Thank you! Im still new to Librepilot and there is a lot to learn...
-
Maybe this page can help you ?
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly
(http://www.dronetrest.com/uploads/db5290/optimized/2X/1/1c1f3b0ca4545356acb068cab8eb4906bfc50b45_1_690x170.JPG)
Q
i like to setup a 3d gimball , so far everything is oke , but missing outputs
current setup , sat,gps,currentsensor,4xESC,osd
i can see that i can easly setup a 2D gimbal but what about 3
does flexi-io port profide output when selecting a telemetry profile? (as i need osd)
anyinfo welkom or even re-config suggestion.
-
Maybe this page can help you ?
https://librepilot.atlassian.net/wiki/display/LPDOC/MinOPOSD+setup#MinOPOSDsetup-Revolutiononly
(http://www.dronetrest.com/uploads/db5290/optimized/2X/1/1c1f3b0ca4545356acb068cab8eb4906bfc50b45_1_690x170.JPG)
Q
i like to setup a 3d gimball , so far everything is oke , but missing outputs
current setup , sat,gps,currentsensor,4xESC,osd
i can see that i can easly setup a 2D gimbal but what about 3
does flexi-io port profide output when selecting a telemetry profile? (as i need osd)
anyinfo welkom or even re-config suggestion.
Found a good setup .
Lemon sat with ppm out now i can remove sat and connect telemerty on that port . giving me 5 outputs for gim.